In the Linux kernel, the following vulnerability has been resolved:
netfilter: nft_payload: incorrect arithmetics when fetching VLAN header bits
If the offset + length goes over the ethernet + vlan header, then the
length is adjusted to copy the bytes that are within the boundaries of
the vlan_ethhdr scratchpad area. The remaining bytes beyond ethernet +
vlan header are copied directly from the skbuff data area.
Fix incorrect arithmetic operator: subtract, not add, the size of the
vlan header in case of double-tagged packets to adjust the length
accordingly to address CVE-2023-0179.
In the Linux kernel, the following vulnerability has been resolved:
netfilter: ipset: Fix overflow before widen in the bitmap_ip_create() function.
When first_ip is 0, last_ip is 0xFFFFFFFF, and netmask is 31, the value of
an arithmetic expression 2 << (netmask - mask_bits - 1) is subject
to overflow due to a failure casting operands to a larger data type
before performing the arithmetic.
Note that it's harmless since the value will be checked at the next step.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
In the Linux kernel, the following vulnerability has been resolved:
powerpc/imc-pmu: Fix use of mutex in IRQs disabled section
Current imc-pmu code triggers a WARNING with CONFIG_DEBUG_ATOMIC_SLEEP
and CONFIG_PROVE_LOCKING enabled, while running a thread_imc event.
Command to trigger the warning:
# perf stat -e thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/ sleep 5
Performance counter stats for 'sleep 5':
0 thread_imc/CPM_CS_FROM_L4_MEM_X_DPTEG/
5.002117947 seconds time elapsed
0.000131000 seconds user
0.001063000 seconds sys
Below is snippet of the warning in dmesg:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 2869, name: perf-exec
preempt_count: 2, expected: 0
4 locks held by perf-exec/2869:
#0: c00000004325c540 (&sig->cred_guard_mutex){+.+.}-{3:3}, at: bprm_execve+0x64/0xa90
#1: c00000004325c5d8 (&sig->exec_update_lock){++++}-{3:3}, at: begin_new_exec+0x460/0xef0
#2: c0000003fa99d4e0 (&cpuctx_lock){-...}-{2:2}, at: perf_event_exec+0x290/0x510
#3: c000000017ab8418 (&ctx->lock){....}-{2:2}, at: perf_event_exec+0x29c/0x510
irq event stamp: 4806
hardirqs last enabled at (4805): [<c000000000f65b94>] _raw_spin_unlock_irqrestore+0x94/0xd0
hardirqs last disabled at (4806): [<c0000000003fae44>] perf_event_exec+0x394/0x510
softirqs last enabled at (0): [<c00000000013c404>] copy_process+0xc34/0x1ff0
softirqs last disabled at (0): [<0000000000000000>] 0x0
CPU: 36 PID: 2869 Comm: perf-exec Not tainted 6.2.0-rc2-00011-g1247637727f2 #61
Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV
Call Trace:
dump_stack_lvl+0x98/0xe0 (unreliable)
__might_resched+0x2f8/0x310
__mutex_lock+0x6c/0x13f0
thread_imc_event_add+0xf4/0x1b0
event_sched_in+0xe0/0x210
merge_sched_in+0x1f0/0x600
visit_groups_merge.isra.92.constprop.166+0x2bc/0x6c0
ctx_flexible_sched_in+0xcc/0x140
ctx_sched_in+0x20c/0x2a0
ctx_resched+0x104/0x1c0
perf_event_exec+0x340/0x510
begin_new_exec+0x730/0xef0
load_elf_binary+0x3f8/0x1e10
...
do not call blocking ops when !TASK_RUNNING; state=2001 set at [<00000000fd63e7cf>] do_nanosleep+0x60/0x1a0
WARNING: CPU: 36 PID: 2869 at kernel/sched/core.c:9912 __might_sleep+0x9c/0xb0
CPU: 36 PID: 2869 Comm: sleep Tainted: G W 6.2.0-rc2-00011-g1247637727f2 #61
Hardware name: 8375-42A POWER9 0x4e1202 opal:v7.0-16-g9b85f7d961 PowerNV
NIP: c000000000194a1c LR: c000000000194a18 CTR: c000000000a78670
REGS: c00000004d2134e0 TRAP: 0700 Tainted: G W (6.2.0-rc2-00011-g1247637727f2)
MSR: 9000000000021033 <SF,HV,ME,IR,DR,RI,LE> CR: 48002824 XER: 00000000
CFAR: c00000000013fb64 IRQMASK: 1
The above warning triggered because the current imc-pmu code uses mutex
lock in interrupt disabled sections. The function mutex_lock()
internally calls __might_resched(), which will check if IRQs are
disabled and in case IRQs are disabled, it will trigger the warning.
Fix the issue by changing the mutex lock to spinlock.
[mpe: Fix comments, trim oops in change log, add reported-by tags]
In the Linux kernel, the following vulnerability has been resolved:
octeontx2-pf: Fix the use of GFP_KERNEL in atomic context on rt
The commit 4af1b64f80fb ("octeontx2-pf: Fix lmtst ID used in aura
free") uses the get/put_cpu() to protect the usage of percpu pointer
in ->aura_freeptr() callback, but it also unnecessarily disable the
preemption for the blockable memory allocation. The commit 87b93b678e95
("octeontx2-pf: Avoid use of GFP_KERNEL in atomic context") tried to
fix these sleep inside atomic warnings. But it only fix the one for
the non-rt kernel. For the rt kernel, we still get the similar warnings
like below.
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:46
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
3 locks held by swapper/0/1:
#0: ffff800009fc5fe8 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x24/0x30
#1: ffff000100c276c0 (&mbox->lock){+.+.}-{3:3}, at: otx2_init_hw_resources+0x8c/0x3a4
#2: ffffffbfef6537e0 (&cpu_rcache->lock){+.+.}-{2:2}, at: alloc_iova_fast+0x1ac/0x2ac
Preemption disabled at:
[<ffff800008b1908c>] otx2_rq_aura_pool_init+0x14c/0x284
CPU: 20 PID: 1 Comm: swapper/0 Tainted: G W 6.2.0-rc3-rt1-yocto-preempt-rt #1
Hardware name: Marvell OcteonTX CN96XX board (DT)
Call trace:
dump_backtrace.part.0+0xe8/0xf4
show_stack+0x20/0x30
dump_stack_lvl+0x9c/0xd8
dump_stack+0x18/0x34
__might_resched+0x188/0x224
rt_spin_lock+0x64/0x110
alloc_iova_fast+0x1ac/0x2ac
iommu_dma_alloc_iova+0xd4/0x110
__iommu_dma_map+0x80/0x144
iommu_dma_map_page+0xe8/0x260
dma_map_page_attrs+0xb4/0xc0
__otx2_alloc_rbuf+0x90/0x150
otx2_rq_aura_pool_init+0x1c8/0x284
otx2_init_hw_resources+0xe4/0x3a4
otx2_open+0xf0/0x610
__dev_open+0x104/0x224
__dev_change_flags+0x1e4/0x274
dev_change_flags+0x2c/0x7c
ic_open_devs+0x124/0x2f8
ip_auto_config+0x180/0x42c
do_one_initcall+0x90/0x4dc
do_basic_setup+0x10c/0x14c
kernel_init_freeable+0x10c/0x13c
kernel_init+0x2c/0x140
ret_from_fork+0x10/0x20
Of course, we can shuffle the get/put_cpu() to only wrap the invocation
of ->aura_freeptr() as what commit 87b93b678e95 does. But there are only
two ->aura_freeptr() callbacks, otx2_aura_freeptr() and
cn10k_aura_freeptr(). There is no usage of perpcu variable in the
otx2_aura_freeptr() at all, so the get/put_cpu() seems redundant to it.
We can move the get/put_cpu() into the corresponding callback which
really has the percpu variable usage and avoid the sprinkling of
get/put_cpu() in several places.
In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Fix ib block iterator counter overflow
When registering a new DMA MR after selecting the best aligned page size
for it, we iterate over the given sglist to split each entry to smaller,
aligned to the selected page size, DMA blocks.
In given circumstances where the sg entry and page size fit certain
sizes and the sg entry is not aligned to the selected page size, the
total size of the aligned pages we need to cover the sg entry is >= 4GB.
Under this circumstances, while iterating page aligned blocks, the
counter responsible for counting how much we advanced from the start of
the sg entry is overflowed because its type is u32 and we pass 4GB in
size. This can lead to an infinite loop inside the iterator function
because the overflow prevents the counter to be larger
than the size of the sg entry.
Fix the presented problem by changing the advancement condition to
eliminate overflow.
Backtrace:
[ 192.374329] efa_reg_user_mr_dmabuf
[ 192.376783] efa_register_mr
[ 192.382579] pgsz_bitmap 0xfffff000 rounddown 0x80000000
[ 192.386423] pg_sz [0x80000000] umem_length[0xc0000000]
[ 192.392657] start 0x0 length 0xc0000000 params.page_shift 31 params.page_num 3
[ 192.399559] hp_cnt[3], pages_in_hp[524288]
[ 192.403690] umem->sgt_append.sgt.nents[1]
[ 192.407905] number entries: [1], pg_bit: [31]
[ 192.411397] biter->__sg_nents [1] biter->__sg [0000000008b0c5d8]
[ 192.415601] biter->__sg_advance [665837568] sg_dma_len[3221225472]
[ 192.419823] biter->__sg_nents [1] biter->__sg [0000000008b0c5d8]
[ 192.423976] biter->__sg_advance [2813321216] sg_dma_len[3221225472]
[ 192.428243] biter->__sg_nents [1] biter->__sg [0000000008b0c5d8]
[ 192.432397] biter->__sg_advance [665837568] sg_dma_len[3221225472]
In the Linux kernel, the following vulnerability has been resolved:
net: enetc: avoid deadlock in enetc_tx_onestep_tstamp()
This lockdep splat says it better than I could:
================================
WARNING: inconsistent lock state
6.2.0-rc2-07010-ga9b9500ffaac-dirty #967 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/1:3/179 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff3ec4036ce098 (_xmit_ETHER#2){+.?.}-{3:3}, at: netif_freeze_queues+0x5c/0xc0
{IN-SOFTIRQ-W} state was registered at:
_raw_spin_lock+0x5c/0xc0
sch_direct_xmit+0x148/0x37c
__dev_queue_xmit+0x528/0x111c
ip6_finish_output2+0x5ec/0xb7c
ip6_finish_output+0x240/0x3f0
ip6_output+0x78/0x360
ndisc_send_skb+0x33c/0x85c
ndisc_send_rs+0x54/0x12c
addrconf_rs_timer+0x154/0x260
call_timer_fn+0xb8/0x3a0
__run_timers.part.0+0x214/0x26c
run_timer_softirq+0x3c/0x74
__do_softirq+0x14c/0x5d8
____do_softirq+0x10/0x20
call_on_irq_stack+0x2c/0x5c
do_softirq_own_stack+0x1c/0x30
__irq_exit_rcu+0x168/0x1a0
irq_exit_rcu+0x10/0x40
el1_interrupt+0x38/0x64
irq event stamp: 7825
hardirqs last enabled at (7825): [<ffffdf1f7200cae4>] exit_to_kernel_mode+0x34/0x130
hardirqs last disabled at (7823): [<ffffdf1f708105f0>] __do_softirq+0x550/0x5d8
softirqs last enabled at (7824): [<ffffdf1f7081050c>] __do_softirq+0x46c/0x5d8
softirqs last disabled at (7811): [<ffffdf1f708166e0>] ____do_softirq+0x10/0x20
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
<Interrupt>
lock(_xmit_ETHER#2);
*** DEADLOCK ***
3 locks held by kworker/1:3/179:
#0: ffff3ec400004748 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x1f4/0x6c0
#1: ffff80000a0bbdc8 ((work_completion)(&priv->tx_onestep_tstamp)){+.+.}-{0:0}, at: process_one_work+0x1f4/0x6c0
#2: ffff3ec4036cd438 (&dev->tx_global_lock){+.+.}-{3:3}, at: netif_tx_lock+0x1c/0x34
Workqueue: events enetc_tx_onestep_tstamp
Call trace:
print_usage_bug.part.0+0x208/0x22c
mark_lock+0x7f0/0x8b0
__lock_acquire+0x7c4/0x1ce0
lock_acquire.part.0+0xe0/0x220
lock_acquire+0x68/0x84
_raw_spin_lock+0x5c/0xc0
netif_freeze_queues+0x5c/0xc0
netif_tx_lock+0x24/0x34
enetc_tx_onestep_tstamp+0x20/0x100
process_one_work+0x28c/0x6c0
worker_thread+0x74/0x450
kthread+0x118/0x11c
but I'll say it anyway: the enetc_tx_onestep_tstamp() work item runs in
process context, therefore with softirqs enabled (i.o.w., it can be
interrupted by a softirq). If we hold the netif_tx_lock() when there is
an interrupt, and the NET_TX softirq then gets scheduled, this will take
the netif_tx_lock() a second time and deadlock the kernel.
To solve this, use netif_tx_lock_bh(), which blocks softirqs from
running.
In the Linux kernel, the following vulnerability has been resolved:
l2tp: close all race conditions in l2tp_tunnel_register()
The code in l2tp_tunnel_register() is racy in several ways:
1. It modifies the tunnel socket _after_ publishing it.
2. It calls setup_udp_tunnel_sock() on an existing socket without
locking.
3. It changes sock lock class on fly, which triggers many syzbot
reports.
This patch amends all of them by moving socket initialization code
before publishing and under sock lock. As suggested by Jakub, the
l2tp lockdep class is not necessary as we can just switch to
bh_lock_sock_nested().
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_conn: Fix memory leaks
When hci_cmd_sync_queue() failed in hci_le_terminate_big() or
hci_le_big_terminate(), the memory pointed by variable d is not freed,
which will cause memory leak. Add release process to error path.
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: fix memory leak in hci_update_adv_data()
When hci_cmd_sync_queue() failed in hci_update_adv_data(), inst_ptr is
not freed, which will cause memory leak, convert to use ERR_PTR/PTR_ERR
to pass the instance to callback so no memory needs to be allocated.
In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: Fix possible deadlock in rfcomm_sk_state_change
syzbot reports a possible deadlock in rfcomm_sk_state_change [1].
While rfcomm_sock_connect acquires the sk lock and waits for
the rfcomm lock, rfcomm_sock_release could have the rfcomm
lock and hit a deadlock for acquiring the sk lock.
Here's a simplified flow:
rfcomm_sock_connect:
lock_sock(sk)
rfcomm_dlc_open:
rfcomm_lock()
rfcomm_sock_release:
rfcomm_sock_shutdown:
rfcomm_lock()
__rfcomm_dlc_close:
rfcomm_k_state_change:
lock_sock(sk)
This patch drops the sk lock before calling rfcomm_dlc_open to
avoid the possible deadlock and holds sk's reference count to
prevent use-after-free after rfcomm_dlc_open completes.
In the Linux kernel, the following vulnerability has been resolved:
HID: betop: check shape of output reports
betopff_init() only checks the total sum of the report counts for each
report field to be at least 4, but hid_betopff_play() expects 4 report
fields.
A device advertising an output report with one field and 4 report counts
would pass the check but crash the kernel with a NULL pointer dereference
in hid_betopff_play().
In the Linux kernel, the following vulnerability has been resolved:
dmaengine: tegra: Fix memory leak in terminate_all()
Terminate vdesc when terminating an ongoing transfer.
This will ensure that the vdesc is present in the desc_terminated list
The descriptor will be freed later in desc_free_list().
This fixes the memory leaks which can happen when terminating an
ongoing transfer.
In the Linux kernel, the following vulnerability has been resolved:
ptdma: pt_core_execute_cmd() should use spinlock
The interrupt handler (pt_core_irq_handler()) of the ptdma
driver can be called from interrupt context. The code flow
in this function can lead down to pt_core_execute_cmd() which
will attempt to grab a mutex, which is not appropriate in
interrupt context and ultimately leads to a kernel panic.
The fix here changes this mutex to a spinlock, which has
been verified to resolve the issue.
In the Linux kernel, the following vulnerability has been resolved:
thermal: core: call put_device() only after device_register() fails
put_device() shouldn't be called before a prior call to
device_register(). __thermal_cooling_device_register() doesn't follow
that properly and needs fixing. Also
thermal_cooling_device_destroy_sysfs() is getting called unnecessarily
on few error paths.
Fix all this by placing the calls at the right place.
Based on initial work done by Caleb Connolly.
In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: enable all safety features by default
In the original implementation of dwmac5
commit 8bf993a5877e ("net: stmmac: Add support for DWMAC5 and implement Safety Features")
all safety features were enabled by default.
Later it seems some implementations didn't have support for all the
features, so in
commit 5ac712dcdfef ("net: stmmac: enable platform specific safety features")
the safety_feat_cfg structure was added to the callback and defined for
some platforms to selectively enable these safety features.
The problem is that only certain platforms were given that software
support. If the automotive safety package bit is set in the hardware
features register the safety feature callback is called for the platform,
and for platforms that didn't get a safety_feat_cfg defined this results
in the following NULL pointer dereference:
[ 7.933303] Call trace:
[ 7.935812] dwmac5_safety_feat_config+0x20/0x170 [stmmac]
[ 7.941455] __stmmac_open+0x16c/0x474 [stmmac]
[ 7.946117] stmmac_open+0x38/0x70 [stmmac]
[ 7.950414] __dev_open+0x100/0x1dc
[ 7.954006] __dev_change_flags+0x18c/0x204
[ 7.958297] dev_change_flags+0x24/0x6c
[ 7.962237] do_setlink+0x2b8/0xfa4
[ 7.965827] __rtnl_newlink+0x4ec/0x840
[ 7.969766] rtnl_newlink+0x50/0x80
[ 7.973353] rtnetlink_rcv_msg+0x12c/0x374
[ 7.977557] netlink_rcv_skb+0x5c/0x130
[ 7.981500] rtnetlink_rcv+0x18/0x2c
[ 7.985172] netlink_unicast+0x2e8/0x340
[ 7.989197] netlink_sendmsg+0x1a8/0x420
[ 7.993222] ____sys_sendmsg+0x218/0x280
[ 7.997249] ___sys_sendmsg+0xac/0x100
[ 8.001103] __sys_sendmsg+0x84/0xe0
[ 8.004776] __arm64_sys_sendmsg+0x24/0x30
[ 8.008983] invoke_syscall+0x48/0x114
[ 8.012840] el0_svc_common.constprop.0+0xcc/0xec
[ 8.017665] do_el0_svc+0x38/0xb0
[ 8.021071] el0_svc+0x2c/0x84
[ 8.024212] el0t_64_sync_handler+0xf4/0x120
[ 8.028598] el0t_64_sync+0x190/0x194
Go back to the original behavior, if the automotive safety package
is found to be supported in hardware enable all the features unless
safety_feat_cfg is passed in saying this particular platform only
supports a subset of the features.
In the Linux kernel, the following vulnerability has been resolved:
bnxt: Do not read past the end of test names
Test names were being concatenated based on a offset beyond the end of
the first name, which tripped the buffer overflow detection logic:
detected buffer overflow in strnlen
[...]
Call Trace:
bnxt_ethtool_init.cold+0x18/0x18
Refactor struct hwrm_selftest_qlist_output to use an actual array,
and adjust the concatenation to use snprintf() rather than a series of
strncat() calls.
In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Add sync after creating vram bo
There will be data corruption on vram allocated by svm
if the initialization is not complete and application is
writting on the memory. Adding sync to wait for the
initialization completion is to resolve this issue.
In the Linux kernel, the following vulnerability has been resolved:
cifs: fix potential memory leaks in session setup
Make sure to free cifs_ses::auth_key.response before allocating it as
we might end up leaking memory in reconnect or mounting.
In the Linux kernel, the following vulnerability has been resolved:
tracing: Make sure trace_printk() can output as soon as it can be used
Currently trace_printk() can be used as soon as early_trace_init() is
called from start_kernel(). But if a crash happens, and
"ftrace_dump_on_oops" is set on the kernel command line, all you get will
be:
[ 0.456075] <idle>-0 0dN.2. 347519us : Unknown type 6
[ 0.456075] <idle>-0 0dN.2. 353141us : Unknown type 6
[ 0.456075] <idle>-0 0dN.2. 358684us : Unknown type 6
This is because the trace_printk() event (type 6) hasn't been registered
yet. That gets done via an early_initcall(), which may be early, but not
early enough.
Instead of registering the trace_printk() event (and other ftrace events,
which are not trace events) via an early_initcall(), have them registered at
the same time that trace_printk() can be used. This way, if there is a
crash before early_initcall(), then the trace_printk()s will actually be
useful.
In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix oops due to uncleared server->smbd_conn in reconnect
In smbd_destroy(), clear the server->smbd_conn pointer after freeing the
smbd_connection struct that it points to so that reconnection doesn't get
confused.
In the Linux kernel, the following vulnerability has been resolved:
trace_events_hist: add check for return value of 'create_hist_field'
Function 'create_hist_field' is called recursively at
trace_events_hist.c:1954 and can return NULL-value that's why we have
to check it to avoid null pointer dereference.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Fix a memory leak with reused mmap_offset
drm_vma_node_allow() and drm_vma_node_revoke() should be called in
balanced pairs. We call drm_vma_node_allow() once per-file everytime a
user calls mmap_offset, but only call drm_vma_node_revoke once per-file
on each mmap_offset. As the mmap_offset is reused by the client, the
per-file vm_count may remain non-zero and the rbtree leaked.
Call drm_vma_node_allow_once() instead to prevent that memory leak.
In the Linux kernel, the following vulnerability has been resolved:
net: fec: Use page_pool_put_full_page when freeing rx buffers
The page_pool_release_page was used when freeing rx buffers, and this
function just unmaps the page (if mapped) and does not recycle the page.
So after hundreds of down/up the eth0, the system will out of memory.
For more details, please refer to the following reproduce steps and
bug logs. To solve this issue and refer to the doc of page pool, the
page_pool_put_full_page should be used to replace page_pool_release_page.
Because this API will try to recycle the page if the page refcnt equal to
1. After testing 20000 times, the issue can not be reproduced anymore
(about testing 391 times the issue will occur on i.MX8MN-EVK before).
Reproduce steps:
Create the test script and run the script. The script content is as
follows:
LOOPS=20000
i=1
while [ $i -le $LOOPS ]
do
echo "TINFO:ENET $curface up and down test $i times"
org_macaddr=$(cat /sys/class/net/eth0/address)
ifconfig eth0 down
ifconfig eth0 hw ether $org_macaddr up
i=$(expr $i + 1)
done
sleep 5
if cat /sys/class/net/eth0/operstate | grep 'up';then
echo "TEST PASS"
else
echo "TEST FAIL"
fi
Bug detail logs:
TINFO:ENET up and down test 391 times
[ 850.471205] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 853.535318] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 853.541694] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 870.590531] page_pool_release_retry() stalled pool shutdown 199 inflight 60 sec
[ 931.006557] page_pool_release_retry() stalled pool shutdown 199 inflight 120 sec
TINFO:ENET up and down test 392 times
[ 991.426544] page_pool_release_retry() stalled pool shutdown 192 inflight 181 sec
[ 1051.838531] page_pool_release_retry() stalled pool shutdown 170 inflight 241 sec
[ 1093.751217] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 1096.446520] page_pool_release_retry() stalled pool shutdown 308 inflight 60 sec
[ 1096.831245] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1096.839092] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1112.254526] page_pool_release_retry() stalled pool shutdown 103 inflight 302 sec
[ 1156.862533] page_pool_release_retry() stalled pool shutdown 308 inflight 120 sec
[ 1172.674516] page_pool_release_retry() stalled pool shutdown 103 inflight 362 sec
[ 1217.278532] page_pool_release_retry() stalled pool shutdown 308 inflight 181 sec
TINFO:ENET up and down test 393 times
[ 1233.086535] page_pool_release_retry() stalled pool shutdown 103 inflight 422 sec
[ 1277.698513] page_pool_release_retry() stalled pool shutdown 308 inflight 241 sec
[ 1293.502525] page_pool_release_retry() stalled pool shutdown 86 inflight 483 sec
[ 1338.110518] page_pool_release_retry() stalled pool shutdown 308 inflight 302 sec
[ 1353.918540] page_pool_release_retry() stalled pool shutdown 32 inflight 543 sec
[ 1361.179205] Qualcomm Atheros AR8031/AR8033 30be0000.ethernet-1:00: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:00, irq=POLL)
[ 1364.255298] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1364.263189] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1371.998532] page_pool_release_retry() stalled pool shutdown 310 inflight 60 sec
[ 1398.530542] page_pool_release_retry() stalled pool shutdown 308 inflight 362 sec
[ 1414.334539] page_pool_release_retry() stalled pool shutdown 16 inflight 604 sec
[ 1432.414520] page_pool_release_retry() stalled pool shutdown 310 inflight 120 sec
[ 1458.942523] page_pool_release_retry() stalled pool shutdown 308 inflight 422 sec
[ 1474.750521] page_pool_release_retry() stalled pool shutdown 16 inflight 664 sec
TINFO:ENET up and down test 394 times
[ 1492.8305
---truncated---
In the Linux kernel, the following vulnerability has been resolved:
ipv4: prevent potential spectre v1 gadget in ip_metrics_convert()
if (!type)
continue;
if (type > RTAX_MAX)
return -EINVAL;
...
metrics[type - 1] = val;
@type being used as an array index, we need to prevent
cpu speculation or risk leaking kernel memory content.
In the Linux kernel, the following vulnerability has been resolved:
ipv4: prevent potential spectre v1 gadget in fib_metrics_match()
if (!type)
continue;
if (type > RTAX_MAX)
return false;
...
fi_val = fi->fib_metrics->metrics[type - 1];
@type being used as an array index, we need to prevent
cpu speculation or risk leaking kernel memory content.
In the Linux kernel, the following vulnerability has been resolved:
x86/i8259: Mark legacy PIC interrupts with IRQ_LEVEL
Baoquan reported that after triggering a crash the subsequent crash-kernel
fails to boot about half of the time. It triggers a NULL pointer
dereference in the periodic tick code.
This happens because the legacy timer interrupt (IRQ0) is resent in
software which happens in soft interrupt (tasklet) context. In this context
get_irq_regs() returns NULL which leads to the NULL pointer dereference.
The reason for the resend is a spurious APIC interrupt on the IRQ0 vector
which is captured and leads to a resend when the legacy timer interrupt is
enabled. This is wrong because the legacy PIC interrupts are level
triggered and therefore should never be resent in software, but nothing
ever sets the IRQ_LEVEL flag on those interrupts, so the core code does not
know about their trigger type.
Ensure that IRQ_LEVEL is set when the legacy PCI interrupts are set up.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Skip task with pid=1 in send_signal_common()
The following kernel panic can be triggered when a task with pid=1 attaches
a prog that attempts to send killing signal to itself, also see [1] for more
details:
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
CPU: 3 PID: 1 Comm: systemd Not tainted 6.1.0-09652-g59fe41b5255f #148
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x100/0x178 lib/dump_stack.c:106
panic+0x2c4/0x60f kernel/panic.c:275
do_exit.cold+0x63/0xe4 kernel/exit.c:789
do_group_exit+0xd4/0x2a0 kernel/exit.c:950
get_signal+0x2460/0x2600 kernel/signal.c:2858
arch_do_signal_or_restart+0x78/0x5d0 arch/x86/kernel/signal.c:306
exit_to_user_mode_loop kernel/entry/common.c:168 [inline]
exit_to_user_mode_prepare+0x15f/0x250 kernel/entry/common.c:203
__syscall_exit_to_user_mode_work kernel/entry/common.c:285 [inline]
syscall_exit_to_user_mode+0x1d/0x50 kernel/entry/common.c:296
do_syscall_64+0x44/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
So skip task with pid=1 in bpf_send_signal_common() to avoid the panic.
[1] https://lore.kernel.org/bpf/20221222043507.33037-1-sunhao.th@gmail.com
In the Linux kernel, the following vulnerability has been resolved:
net: fix NULL pointer in skb_segment_list
Commit 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.")
introduced UDP listifyed GRO. The segmentation relies on frag_list being
untouched when passing through the network stack. This assumption can be
broken sometimes, where frag_list itself gets pulled into linear area,
leaving frag_list being NULL. When this happens it can trigger
following NULL pointer dereference, and panic the kernel. Reverse the
test condition should fix it.
[19185.577801][ C1] BUG: kernel NULL pointer dereference, address:
...
[19185.663775][ C1] RIP: 0010:skb_segment_list+0x1cc/0x390
...
[19185.834644][ C1] Call Trace:
[19185.841730][ C1] <TASK>
[19185.848563][ C1] __udp_gso_segment+0x33e/0x510
[19185.857370][ C1] inet_gso_segment+0x15b/0x3e0
[19185.866059][ C1] skb_mac_gso_segment+0x97/0x110
[19185.874939][ C1] __skb_gso_segment+0xb2/0x160
[19185.883646][ C1] udp_queue_rcv_skb+0xc3/0x1d0
[19185.892319][ C1] udp_unicast_rcv_skb+0x75/0x90
[19185.900979][ C1] ip_protocol_deliver_rcu+0xd2/0x200
[19185.910003][ C1] ip_local_deliver_finish+0x44/0x60
[19185.918757][ C1] __netif_receive_skb_one_core+0x8b/0xa0
[19185.927834][ C1] process_backlog+0x88/0x130
[19185.935840][ C1] __napi_poll+0x27/0x150
[19185.943447][ C1] net_rx_action+0x27e/0x5f0
[19185.951331][ C1] ? mlx5_cq_tasklet_cb+0x70/0x160 [mlx5_core]
[19185.960848][ C1] __do_softirq+0xbc/0x25d
[19185.968607][ C1] irq_exit_rcu+0x83/0xb0
[19185.976247][ C1] common_interrupt+0x43/0xa0
[19185.984235][ C1] asm_common_interrupt+0x22/0x40
...
[19186.094106][ C1] </TASK>
In the Linux kernel, the following vulnerability has been resolved:
firewire: fix memory leak for payload of request subaction to IEC 61883-1 FCP region
This patch is fix for Linux kernel v2.6.33 or later.
For request subaction to IEC 61883-1 FCP region, Linux FireWire subsystem
have had an issue of use-after-free. The subsystem allows multiple
user space listeners to the region, while data of the payload was likely
released before the listeners execute read(2) to access to it for copying
to user space.
The issue was fixed by a commit 281e20323ab7 ("firewire: core: fix
use-after-free regression in FCP handler"). The object of payload is
duplicated in kernel space for each listener. When the listener executes
ioctl(2) with FW_CDEV_IOC_SEND_RESPONSE request, the object is going to
be released.
However, it causes memory leak since the commit relies on call of
release_request() in drivers/firewire/core-cdev.c. Against the
expectation, the function is never called due to the design of
release_client_resource(). The function delegates release task
to caller when called with non-NULL fourth argument. The implementation
of ioctl_send_response() is the case. It should release the object
explicitly.
This commit fixes the bug.
In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Check for any of tcp_bpf_prots when cloning a listener
A listening socket linked to a sockmap has its sk_prot overridden. It
points to one of the struct proto variants in tcp_bpf_prots. The variant
depends on the socket's family and which sockmap programs are attached.
A child socket cloned from a TCP listener initially inherits their sk_prot.
But before cloning is finished, we restore the child's proto to the
listener's original non-tcp_bpf_prots one. This happens in
tcp_create_openreq_child -> tcp_bpf_clone.
Today, in tcp_bpf_clone we detect if the child's proto should be restored
by checking only for the TCP_BPF_BASE proto variant. This is not
correct. The sk_prot of listening socket linked to a sockmap can point to
to any variant in tcp_bpf_prots.
If the listeners sk_prot happens to be not the TCP_BPF_BASE variant, then
the child socket unintentionally is left if the inherited sk_prot by
tcp_bpf_clone.
This leads to issues like infinite recursion on close [1], because the
child state is otherwise not set up for use with tcp_bpf_prot operations.
Adjust the check in tcp_bpf_clone to detect all of tcp_bpf_prots variants.
Note that it wouldn't be sufficient to check the socket state when
overriding the sk_prot in tcp_bpf_update_proto in order to always use the
TCP_BPF_BASE variant for listening sockets. Since commit
b8b8315e39ff ("bpf, sockmap: Remove unhash handler for BPF sockmap usage")
it is possible for a socket to transition to TCP_LISTEN state while already
linked to a sockmap, e.g. connect() -> insert into map ->
connect(AF_UNSPEC) -> listen().
[1]: https://lore.kernel.org/all/00000000000073b14905ef2e7401@google.com/
In the Linux kernel, the following vulnerability has been resolved:
arm64: dts: imx8mm-verdin: Do not power down eth-phy
Currently if suspending using either freeze or memory state, the fec
driver tries to power down the phy which leads to crash of the kernel
and non-responsible kernel with the following call trace:
[ 24.839889 ] Call trace:
[ 24.839892 ] phy_error+0x18/0x60
[ 24.839898 ] kszphy_handle_interrupt+0x6c/0x80
[ 24.839903 ] phy_interrupt+0x20/0x2c
[ 24.839909 ] irq_thread_fn+0x30/0xa0
[ 24.839919 ] irq_thread+0x178/0x2c0
[ 24.839925 ] kthread+0x154/0x160
[ 24.839932 ] ret_from_fork+0x10/0x20
Since there is currently no functionality in the phy subsystem to power
down phys let's just disable the feature of powering-down the ethernet
phy.
In the Linux kernel, the following vulnerability has been resolved:
net: phy: dp83822: Fix null pointer access on DP83825/DP83826 devices
The probe() function is only used for the DP83822 PHY, leaving the
private data pointer uninitialized for the smaller DP83825/26 models.
While all uses of the private data structure are hidden in 82822 specific
callbacks, configuring the interrupt is shared across all models.
This causes a NULL pointer dereference on the smaller PHYs as it accesses
the private data unchecked. Verifying the pointer avoids that.
In the Linux kernel, the following vulnerability has been resolved:
fscache: Use wait_on_bit() to wait for the freeing of relinquished volume
The freeing of relinquished volume will wake up the pending volume
acquisition by using wake_up_bit(), however it is mismatched with
wait_var_event() used in fscache_wait_on_volume_collision() and it will
never wake up the waiter in the wait-queue because these two functions
operate on different wait-queues.
According to the implementation in fscache_wait_on_volume_collision(),
if the wake-up of pending acquisition is delayed longer than 20 seconds
(e.g., due to the delay of on-demand fd closing), the first
wait_var_event_timeout() will timeout and the following wait_var_event()
will hang forever as shown below:
FS-Cache: Potential volume collision new=00000024 old=00000022
......
INFO: task mount:1148 blocked for more than 122 seconds.
Not tainted 6.1.0-rc6+ #1
task:mount state:D stack:0 pid:1148 ppid:1
Call Trace:
<TASK>
__schedule+0x2f6/0xb80
schedule+0x67/0xe0
fscache_wait_on_volume_collision.cold+0x80/0x82
__fscache_acquire_volume+0x40d/0x4e0
erofs_fscache_register_volume+0x51/0xe0 [erofs]
erofs_fscache_register_fs+0x19c/0x240 [erofs]
erofs_fc_fill_super+0x746/0xaf0 [erofs]
vfs_get_super+0x7d/0x100
get_tree_nodev+0x16/0x20
erofs_fc_get_tree+0x20/0x30 [erofs]
vfs_get_tree+0x24/0xb0
path_mount+0x2fa/0xa90
do_mount+0x7c/0xa0
__x64_sys_mount+0x8b/0xe0
do_syscall_64+0x30/0x60
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Considering that wake_up_bit() is more selective, so fix it by using
wait_on_bit() instead of wait_var_event() to wait for the freeing of
relinquished volume. In addition because waitqueue_active() is used in
wake_up_bit() and clear_bit() doesn't imply any memory barrier, use
clear_and_wake_up_bit() to add the missing memory barrier between
cursor->flags and waitqueue_active().
In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Fix request ref counting during error capture & debugfs dump
When GuC support was added to error capture, the reference counting
around the request object was broken. Fix it up.
The context based search manages the spinlocking around the search
internally. So it needs to grab the reference count internally as
well. The execlist only request based search relies on external
locking, so it needs an external reference count but within the
spinlock not outside it.
The only other caller of the context based search is the code for
dumping engine state to debugfs. That code wasn't previously getting
an explicit reference at all as it does everything while holding the
execlist specific spinlock. So, that needs updaing as well as that
spinlock doesn't help when using GuC submission. Rather than trying to
conditionally get/put depending on submission model, just change it to
always do the get/put.
v2: Explicitly document adding an extra blank line in some dense code
(Andy Shevchenko). Fix multiple potential null pointer derefs in case
of no request found (some spotted by Tvrtko, but there was more!).
Also fix a leaked request in case of !started and another in
__guc_reset_context now that intel_context_find_active_request is
actually reference counting the returned request.
v3: Add a _get suffix to intel_context_find_active_request now that it
grabs a reference (Daniele).
v4: Split the intel_guc_find_hung_context change to a separate patch
and rename intel_context_find_active_request_get to
intel_context_get_active_request (Tvrtko).
v5: s/locking/reference counting/ in commit message (Tvrtko)
(cherry picked from commit 3700e353781e27f1bc7222f51f2cc36cbeb9b4ec)
In the Linux kernel, the following vulnerability has been resolved:
riscv: kprobe: Fixup kernel panic when probing an illegal position
The kernel would panic when probed for an illegal position. eg:
(CONFIG_RISCV_ISA_C=n)
echo 'p:hello kernel_clone+0x16 a0=%a0' >> kprobe_events
echo 1 > events/kprobes/hello/enable
cat trace
Kernel panic - not syncing: stack-protector: Kernel stack
is corrupted in: __do_sys_newfstatat+0xb8/0xb8
CPU: 0 PID: 111 Comm: sh Not tainted
6.2.0-rc1-00027-g2d398fe49a4d #490
Hardware name: riscv-virtio,qemu (DT)
Call Trace:
[<ffffffff80007268>] dump_backtrace+0x38/0x48
[<ffffffff80c5e83c>] show_stack+0x50/0x68
[<ffffffff80c6da28>] dump_stack_lvl+0x60/0x84
[<ffffffff80c6da6c>] dump_stack+0x20/0x30
[<ffffffff80c5ecf4>] panic+0x160/0x374
[<ffffffff80c6db94>] generic_handle_arch_irq+0x0/0xa8
[<ffffffff802deeb0>] sys_newstat+0x0/0x30
[<ffffffff800158c0>] sys_clone+0x20/0x30
[<ffffffff800039e8>] ret_from_syscall+0x0/0x4
---[ end Kernel panic - not syncing: stack-protector:
Kernel stack is corrupted in: __do_sys_newfstatat+0xb8/0xb8 ]---
That is because the kprobe's ebreak instruction broke the kernel's
original code. The user should guarantee the correction of the probe
position, but it couldn't make the kernel panic.
This patch adds arch_check_kprobe in arch_prepare_kprobe to prevent an
illegal position (Such as the middle of an instruction).
In the Linux kernel, the following vulnerability has been resolved:
efi: fix potential NULL deref in efi_mem_reserve_persistent
When iterating on a linked list, a result of memremap is dereferenced
without checking it for NULL.
This patch adds a check that falls back on allocating a new page in
case memremap doesn't succeed.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
[ardb: return -ENOMEM instead of breaking out of the loop]
In the Linux kernel, the following vulnerability has been resolved:
cgroup/cpuset: Fix wrong check in update_parent_subparts_cpumask()
It was found that the check to see if a partition could use up all
the cpus from the parent cpuset in update_parent_subparts_cpumask()
was incorrect. As a result, it is possible to leave parent with no
effective cpu left even if there are tasks in the parent cpuset. This
can lead to system panic as reported in [1].
Fix this probem by updating the check to fail the enabling the partition
if parent's effective_cpus is a subset of the child's cpus_allowed.
Also record the error code when an error happens in update_prstate()
and add a test case where parent partition and child have the same cpu
list and parent has task. Enabling partition in the child will fail in
this case.
[1] https://www.spinics.net/lists/cgroups/msg36254.html
In the Linux kernel, the following vulnerability has been resolved:
can: isotp: split tx timer into transmission and timeout
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
In the Linux kernel, the following vulnerability has been resolved:
mm: multi-gen LRU: fix crash during cgroup migration
lru_gen_migrate_mm() assumes lru_gen_add_mm() runs prior to itself. This
isn't true for the following scenario:
CPU 1 CPU 2
clone()
cgroup_can_fork()
cgroup_procs_write()
cgroup_post_fork()
task_lock()
lru_gen_migrate_mm()
task_unlock()
task_lock()
lru_gen_add_mm()
task_unlock()
And when the above happens, kernel crashes because of linked list
corruption (mm_struct->lru_gen.list).
In the Linux kernel, the following vulnerability has been resolved:
mm: memcg: fix NULL pointer in mem_cgroup_track_foreign_dirty_slowpath()
As commit 18365225f044 ("hwpoison, memcg: forcibly uncharge LRU pages"),
hwpoison will forcibly uncharg a LRU hwpoisoned page, the folio_memcg
could be NULl, then, mem_cgroup_track_foreign_dirty_slowpath() could
occurs a NULL pointer dereference, let's do not record the foreign
writebacks for folio memcg is null in mem_cgroup_track_foreign_dirty() to
fix it.
In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: Don't attempt to resume the ports before they exist
This will fix null pointer dereference that was caused by
the driver attempting to resume ports that were not yet
registered.
In the Linux kernel, the following vulnerability has been resolved:
HV: hv_balloon: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
In the Linux kernel, the following vulnerability has been resolved:
kernel/irq/irqdomain.c: fix memory leak with using debugfs_lookup()
When calling debugfs_lookup() the result must have dput() called on it,
otherwise the memory will leak over time. To make things simpler, just
call debugfs_lookup_and_remove() instead which handles all of the logic
at once.
In the Linux kernel, the following vulnerability has been resolved:
mm/MADV_COLLAPSE: catch !none !huge !bad pmd lookups
In commit 34488399fa08 ("mm/madvise: add file and shmem support to
MADV_COLLAPSE") we make the following change to find_pmd_or_thp_or_none():
- if (!pmd_present(pmde))
- return SCAN_PMD_NULL;
+ if (pmd_none(pmde))
+ return SCAN_PMD_NONE;
This was for-use by MADV_COLLAPSE file/shmem codepaths, where
MADV_COLLAPSE might identify a pte-mapped hugepage, only to have
khugepaged race-in, free the pte table, and clear the pmd. Such codepaths
include:
A) If we find a suitably-aligned compound page of order HPAGE_PMD_ORDER
already in the pagecache.
B) In retract_page_tables(), if we fail to grab mmap_lock for the target
mm/address.
In these cases, collapse_pte_mapped_thp() really does expect a none (not
just !present) pmd, and we want to suitably identify that case separate
from the case where no pmd is found, or it's a bad-pmd (of course, many
things could happen once we drop mmap_lock, and the pmd could plausibly
undergo multiple transitions due to intervening fault, split, etc).
Regardless, the code is prepared install a huge-pmd only when the existing
pmd entry is either a genuine pte-table-mapping-pmd, or the none-pmd.
However, the commit introduces a logical hole; namely, that we've allowed
!none- && !huge- && !bad-pmds to be classified as genuine
pte-table-mapping-pmds. One such example that could leak through are swap
entries. The pmd values aren't checked again before use in
pte_offset_map_lock(), which is expecting nothing less than a genuine
pte-table-mapping-pmd.
We want to put back the !pmd_present() check (below the pmd_none() check),
but need to be careful to deal with subtleties in pmd transitions and
treatments by various arch.
The issue is that __split_huge_pmd_locked() temporarily clears the present
bit (or otherwise marks the entry as invalid), but pmd_present() and
pmd_trans_huge() still need to return true while the pmd is in this
transitory state. For example, x86's pmd_present() also checks the
_PAGE_PSE , riscv's version also checks the _PAGE_LEAF bit, and arm64 also
checks a PMD_PRESENT_INVALID bit.
Covering all 4 cases for x86 (all checks done on the same pmd value):
1) pmd_present() && pmd_trans_huge()
All we actually know here is that the PSE bit is set. Either:
a) We aren't racing with __split_huge_page(), and PRESENT or PROTNONE
is set.
=> huge-pmd
b) We are currently racing with __split_huge_page(). The danger here
is that we proceed as-if we have a huge-pmd, but really we are
looking at a pte-mapping-pmd. So, what is the risk of this
danger?
The only relevant path is:
madvise_collapse() -> collapse_pte_mapped_thp()
Where we might just incorrectly report back "success", when really
the memory isn't pmd-backed. This is fine, since split could
happen immediately after (actually) successful madvise_collapse().
So, it should be safe to just assume huge-pmd here.
2) pmd_present() && !pmd_trans_huge()
Either:
a) PSE not set and either PRESENT or PROTNONE is.
=> pte-table-mapping pmd (or PROT_NONE)
b) devmap. This routine can be called immediately after
unlocking/locking mmap_lock -- or called with no locks held (see
khugepaged_scan_mm_slot()), so previous VMA checks have since been
invalidated.
3) !pmd_present() && pmd_trans_huge()
Not possible.
4) !pmd_present() && !pmd_trans_huge()
Neither PRESENT nor PROTNONE set
=> not present
I've checked all archs that implement pmd_trans_huge() (arm64, riscv,
powerpc, longarch, x86, mips, s390) and this logic roughly translates
(though devmap treatment is unique to x86 and powerpc, and (3) doesn't
necessarily hold in general -- but that doesn't matter since
!pmd_present() always takes failure path).
Also, add a comment above find_pmd_or_thp_or_none()
---truncated---