CVE Database

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_thin_linear_timeouts. While reading sysctl_tcp_thin_linear_timeouts, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_recovery. While reading sysctl_tcp_recovery, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix a data-race around sysctl_tcp_early_retrans. While reading sysctl_tcp_early_retrans, it can be changed concurrently. Thus, we need to add READ_ONCE() to its reader.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_slow_start_after_idle. While reading sysctl_tcp_slow_start_after_idle, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: tcp: Fix data-races around sysctl_tcp_max_reordering. While reading sysctl_tcp_max_reordering, it can be changed concurrently. Thus, we need to add READ_ONCE() to its readers.

In the Linux kernel, the following vulnerability has been resolved: gpio: gpio-xilinx: Fix integer overflow Current implementation is not able to configure more than 32 pins due to incorrect data type. So type casting with unsigned long to avoid it.

In the Linux kernel, the following vulnerability has been resolved: spi: bcm2835: bcm2835_spi_handle_err(): fix NULL pointer deref for non DMA transfers In case a IRQ based transfer times out the bcm2835_spi_handle_err() function is called. Since commit 1513ceee70f2 ("spi: bcm2835: Drop dma_pending flag") the TX and RX DMA transfers are unconditionally canceled, leading to NULL pointer derefs if ctlr->dma_tx or ctlr->dma_rx are not set. Fix the NULL pointer deref by checking that ctlr->dma_tx and ctlr->dma_rx are valid pointers before accessing them.

In the Linux kernel, the following vulnerability has been resolved: KVM: Don't null dereference ops->destroy A KVM device cleanup happens in either of two callbacks: 1) destroy() which is called when the VM is being destroyed; 2) release() which is called when a device fd is closed. Most KVM devices use 1) but Book3s's interrupt controller KVM devices (XICS, XIVE, XIVE-native) use 2) as they need to close and reopen during the machine execution. The error handling in kvm_ioctl_create_device() assumes destroy() is always defined which leads to NULL dereference as discovered by Syzkaller. This adds a checks for destroy!=NULL and adds a missing release(). This is not changing kvm_destroy_devices() as devices with defined release() should have been removed from the KVM devices list by then.

In the Linux kernel, the following vulnerability has been resolved: mm/mempolicy: fix uninit-value in mpol_rebind_policy() mpol_set_nodemask()(mm/mempolicy.c) does not set up nodemask when pol->mode is MPOL_LOCAL. Check pol->mode before access pol->w.cpuset_mems_allowed in mpol_rebind_policy()(mm/mempolicy.c). BUG: KMSAN: uninit-value in mpol_rebind_policy mm/mempolicy.c:352 [inline] BUG: KMSAN: uninit-value in mpol_rebind_task+0x2ac/0x2c0 mm/mempolicy.c:368 mpol_rebind_policy mm/mempolicy.c:352 [inline] mpol_rebind_task+0x2ac/0x2c0 mm/mempolicy.c:368 cpuset_change_task_nodemask kernel/cgroup/cpuset.c:1711 [inline] cpuset_attach+0x787/0x15e0 kernel/cgroup/cpuset.c:2278 cgroup_migrate_execute+0x1023/0x1d20 kernel/cgroup/cgroup.c:2515 cgroup_migrate kernel/cgroup/cgroup.c:2771 [inline] cgroup_attach_task+0x540/0x8b0 kernel/cgroup/cgroup.c:2804 __cgroup1_procs_write+0x5cc/0x7a0 kernel/cgroup/cgroup-v1.c:520 cgroup1_tasks_write+0x94/0xb0 kernel/cgroup/cgroup-v1.c:539 cgroup_file_write+0x4c2/0x9e0 kernel/cgroup/cgroup.c:3852 kernfs_fop_write_iter+0x66a/0x9f0 fs/kernfs/file.c:296 call_write_iter include/linux/fs.h:2162 [inline] new_sync_write fs/read_write.c:503 [inline] vfs_write+0x1318/0x2030 fs/read_write.c:590 ksys_write+0x28b/0x510 fs/read_write.c:643 __do_sys_write fs/read_write.c:655 [inline] __se_sys_write fs/read_write.c:652 [inline] __x64_sys_write+0xdb/0x120 fs/read_write.c:652 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae Uninit was created at: slab_post_alloc_hook mm/slab.h:524 [inline] slab_alloc_node mm/slub.c:3251 [inline] slab_alloc mm/slub.c:3259 [inline] kmem_cache_alloc+0x902/0x11c0 mm/slub.c:3264 mpol_new mm/mempolicy.c:293 [inline] do_set_mempolicy+0x421/0xb70 mm/mempolicy.c:853 kernel_set_mempolicy mm/mempolicy.c:1504 [inline] __do_sys_set_mempolicy mm/mempolicy.c:1510 [inline] __se_sys_set_mempolicy+0x44c/0xb60 mm/mempolicy.c:1507 __x64_sys_set_mempolicy+0xd8/0x110 mm/mempolicy.c:1507 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x54/0xd0 arch/x86/entry/common.c:82 entry_SYSCALL_64_after_hwframe+0x44/0xae KMSAN: uninit-value in mpol_rebind_task (2) https://syzkaller.appspot.com/bug?id=d6eb90f952c2a5de9ea718a1b873c55cb13b59dc This patch seems to fix below bug too. KMSAN: uninit-value in mpol_rebind_mm (2) https://syzkaller.appspot.com/bug?id=f2fecd0d7013f54ec4162f60743a2b28df40926b The uninit-value is pol->w.cpuset_mems_allowed in mpol_rebind_policy(). When syzkaller reproducer runs to the beginning of mpol_new(), mpol_new() mm/mempolicy.c do_mbind() mm/mempolicy.c kernel_mbind() mm/mempolicy.c `mode` is 1(MPOL_PREFERRED), nodes_empty(*nodes) is `true` and `flags` is 0. Then mode = MPOL_LOCAL; ... policy->mode = mode; policy->flags = flags; will be executed. So in mpol_set_nodemask(), mpol_set_nodemask() mm/mempolicy.c do_mbind() kernel_mbind() pol->mode is 4 (MPOL_LOCAL), that `nodemask` in `pol` is not initialized, which will be accessed in mpol_rebind_policy().

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - fix memory leak in RSA When an RSA key represented in form 2 (as defined in PKCS #1 V2.1) is used, some components of the private key persist even after the TFM is released. Replace the explicit calls to free the buffers in qat_rsa_exit_tfm() with a call to qat_rsa_clear_ctx() which frees all buffers referenced in the TFM context.

In the Linux kernel, the following vulnerability has been resolved: perf/x86/intel/lbr: Fix unchecked MSR access error on HSW The fuzzer triggers the below trace. [ 7763.384369] unchecked MSR access error: WRMSR to 0x689 (tried to write 0x1fffffff8101349e) at rIP: 0xffffffff810704a4 (native_write_msr+0x4/0x20) [ 7763.397420] Call Trace: [ 7763.399881] <TASK> [ 7763.401994] intel_pmu_lbr_restore+0x9a/0x1f0 [ 7763.406363] intel_pmu_lbr_sched_task+0x91/0x1c0 [ 7763.410992] __perf_event_task_sched_in+0x1cd/0x240 On a machine with the LBR format LBR_FORMAT_EIP_FLAGS2, when the TSX is disabled, a TSX quirk is required to access LBR from registers. The lbr_from_signext_quirk_needed() is introduced to determine whether the TSX quirk should be applied. However, the lbr_from_signext_quirk_needed() is invoked before the intel_pmu_lbr_init(), which parses the LBR format information. Without the correct LBR format information, the TSX quirk never be applied. Move the lbr_from_signext_quirk_needed() into the intel_pmu_lbr_init(). Checking x86_pmu.lbr_has_tsx in the lbr_from_signext_quirk_needed() is not required anymore. Both LBR_FORMAT_EIP_FLAGS2 and LBR_FORMAT_INFO have LBR_TSX flag, but only the LBR_FORMAT_EIP_FLAGS2 requirs the quirk. Update the comments accordingly.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - add param check for DH Reject requests with a source buffer that is bigger than the size of the key. This is to prevent a possible integer underflow that might happen when copying the source scatterlist into a linear buffer.

In the Linux kernel, the following vulnerability has been resolved: crypto: qat - add param check for RSA Reject requests with a source buffer that is bigger than the size of the key. This is to prevent a possible integer underflow that might happen when copying the source scatterlist into a linear buffer.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Use __try_cmpxchg_user() to update guest PTE A/D bits Use the recently introduced __try_cmpxchg_user() to update guest PTE A/D bits instead of mapping the PTE into kernel address space. The VM_PFNMAP path is broken as it assumes that vm_pgoff is the base pfn of the mapped VMA range, which is conceptually wrong as vm_pgoff is the offset relative to the file and has nothing to do with the pfn. The horrific hack worked for the original use case (backing guest memory with /dev/mem), but leads to accessing "random" pfns for pretty much any other VM_PFNMAP case.

In the Linux kernel, the following vulnerability has been resolved: netfilter: conntrack: re-fetch conntrack after insertion In case the conntrack is clashing, insertion can free skb->_nfct and set skb->_nfct to the already-confirmed entry. This wasn't found before because the conntrack entry and the extension space used to free'd after an rcu grace period, plus the race needs events enabled to trigger.

In the Linux kernel, the following vulnerability has been resolved: KVM: x86: Drop WARNs that assert a triple fault never "escapes" from L2 Remove WARNs that sanity check that KVM never lets a triple fault for L2 escape and incorrectly end up in L1. In normal operation, the sanity check is perfectly valid, but it incorrectly assumes that it's impossible for userspace to induce KVM_REQ_TRIPLE_FAULT without bouncing through KVM_RUN (which guarantees kvm_check_nested_state() will see and handle the triple fault). The WARN can currently be triggered if userspace injects a machine check while L2 is active and CR4.MCE=0. And a future fix to allow save/restore of KVM_REQ_TRIPLE_FAULT, e.g. so that a synthesized triple fault isn't lost on migration, will make it trivially easy for userspace to trigger the WARN. Clearing KVM_REQ_TRIPLE_FAULT when forcibly leaving guest mode is tempting, but wrong, especially if/when the request is saved/restored, e.g. if userspace restores events (including a triple fault) and then restores nested state (which may forcibly leave guest mode). Ignoring the fact that KVM doesn't currently provide the necessary APIs, it's userspace's responsibility to manage pending events during save/restore. ------------[ cut here ]------------ WARNING: CPU: 7 PID: 1399 at arch/x86/kvm/vmx/nested.c:4522 nested_vmx_vmexit+0x7fe/0xd90 [kvm_intel] Modules linked in: kvm_intel kvm irqbypass CPU: 7 PID: 1399 Comm: state_test Not tainted 5.17.0-rc3+ #808 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 RIP: 0010:nested_vmx_vmexit+0x7fe/0xd90 [kvm_intel] Call Trace: <TASK> vmx_leave_nested+0x30/0x40 [kvm_intel] vmx_set_nested_state+0xca/0x3e0 [kvm_intel] kvm_arch_vcpu_ioctl+0xf49/0x13e0 [kvm] kvm_vcpu_ioctl+0x4b9/0x660 [kvm] __x64_sys_ioctl+0x83/0xb0 do_syscall_64+0x3b/0xc0 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK> ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: double hook unregistration in netns path __nft_release_hooks() is called from pre_netns exit path which unregisters the hooks, then the NETDEV_UNREGISTER event is triggered which unregisters the hooks again. [ 565.221461] WARNING: CPU: 18 PID: 193 at net/netfilter/core.c:495 __nf_unregister_net_hook+0x247/0x270 [...] [ 565.246890] CPU: 18 PID: 193 Comm: kworker/u64:1 Tainted: G E 5.18.0-rc7+ #27 [ 565.253682] Workqueue: netns cleanup_net [ 565.257059] RIP: 0010:__nf_unregister_net_hook+0x247/0x270 [...] [ 565.297120] Call Trace: [ 565.300900] <TASK> [ 565.304683] nf_tables_flowtable_event+0x16a/0x220 [nf_tables] [ 565.308518] raw_notifier_call_chain+0x63/0x80 [ 565.312386] unregister_netdevice_many+0x54f/0xb50 Unregister and destroy netdev hook from netns pre_exit via kfree_rcu so the NETDEV_UNREGISTER path see unregistered hooks.

In the Linux kernel, the following vulnerability has been resolved: x86/fpu: KVM: Set the base guest FPU uABI size to sizeof(struct kvm_xsave) Set the starting uABI size of KVM's guest FPU to 'struct kvm_xsave', i.e. to KVM's historical uABI size. When saving FPU state for usersapce, KVM (well, now the FPU) sets the FP+SSE bits in the XSAVE header even if the host doesn't support XSAVE. Setting the XSAVE header allows the VM to be migrated to a host that does support XSAVE without the new host having to handle FPU state that may or may not be compatible with XSAVE. Setting the uABI size to the host's default size results in out-of-bounds writes (setting the FP+SSE bits) and data corruption (that is thankfully caught by KASAN) when running on hosts without XSAVE, e.g. on Core2 CPUs. WARN if the default size is larger than KVM's historical uABI size; all features that can push the FPU size beyond the historical size must be opt-in. ================================================================== BUG: KASAN: slab-out-of-bounds in fpu_copy_uabi_to_guest_fpstate+0x86/0x130 Read of size 8 at addr ffff888011e33a00 by task qemu-build/681 CPU: 1 PID: 681 Comm: qemu-build Not tainted 5.18.0-rc5-KASAN-amd64 #1 Hardware name: /DG35EC, BIOS ECG3510M.86A.0118.2010.0113.1426 01/13/2010 Call Trace: <TASK> dump_stack_lvl+0x34/0x45 print_report.cold+0x45/0x575 kasan_report+0x9b/0xd0 fpu_copy_uabi_to_guest_fpstate+0x86/0x130 kvm_arch_vcpu_ioctl+0x72a/0x1c50 [kvm] kvm_vcpu_ioctl+0x47f/0x7b0 [kvm] __x64_sys_ioctl+0x5de/0xc90 do_syscall_64+0x31/0x50 entry_SYSCALL_64_after_hwframe+0x44/0xae </TASK> Allocated by task 0: (stack is not available) The buggy address belongs to the object at ffff888011e33800 which belongs to the cache kmalloc-512 of size 512 The buggy address is located 0 bytes to the right of 512-byte region [ffff888011e33800, ffff888011e33a00) The buggy address belongs to the physical page: page:0000000089cd4adb refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x11e30 head:0000000089cd4adb order:2 compound_mapcount:0 compound_pincount:0 flags: 0x4000000000010200(slab|head|zone=1) raw: 4000000000010200 dead000000000100 dead000000000122 ffff888001041c80 raw: 0000000000000000 0000000080100010 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff888011e33900: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888011e33980: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffff888011e33a00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ^ ffff888011e33a80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888011e33b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ================================================================== Disabling lock debugging due to kernel taint

In the Linux kernel, the following vulnerability has been resolved: Bluetooth: hci_qca: Use del_timer_sync() before freeing While looking at a crash report on a timer list being corrupted, which usually happens when a timer is freed while still active. This is commonly triggered by code calling del_timer() instead of del_timer_sync() just before freeing. One possible culprit is the hci_qca driver, which does exactly that. Eric mentioned that wake_retrans_timer could be rearmed via the work queue, so also move the destruction of the work queue before del_timer_sync().

In the Linux kernel, the following vulnerability has been resolved: zsmalloc: fix races between asynchronous zspage free and page migration The asynchronous zspage free worker tries to lock a zspage's entire page list without defending against page migration. Since pages which haven't yet been locked can concurrently migrate off the zspage page list while lock_zspage() churns away, lock_zspage() can suffer from a few different lethal races. It can lock a page which no longer belongs to the zspage and unsafely dereference page_private(), it can unsafely dereference a torn pointer to the next page (since there's a data race), and it can observe a spurious NULL pointer to the next page and thus not lock all of the zspage's pages (since a single page migration will reconstruct the entire page list, and create_page_chain() unconditionally zeroes out each list pointer in the process). Fix the races by using migrate_read_lock() in lock_zspage() to synchronize with page migration.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: validate BOOT sectors_per_clusters When the NTFS BOOT sectors_per_clusters field is > 0x80, it represents a shift value. Make sure that the shift value is not too large before using it (NTFS max cluster size is 2MB). Return -EVINVAL if it too large. This prevents negative shift values and shift values that are larger than the field size. Prevents this UBSAN error: UBSAN: shift-out-of-bounds in ../fs/ntfs3/super.c:673:16 shift exponent -192 is negative

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix combination of jit blinding and pointers to bpf subprogs. The combination of jit blinding and pointers to bpf subprogs causes: [ 36.989548] BUG: unable to handle page fault for address: 0000000100000001 [ 36.990342] #PF: supervisor instruction fetch in kernel mode [ 36.990968] #PF: error_code(0x0010) - not-present page [ 36.994859] RIP: 0010:0x100000001 [ 36.995209] Code: Unable to access opcode bytes at RIP 0xffffffd7. [ 37.004091] Call Trace: [ 37.004351] <TASK> [ 37.004576] ? bpf_loop+0x4d/0x70 [ 37.004932] ? bpf_prog_3899083f75e4c5de_F+0xe3/0x13b The jit blinding logic didn't recognize that ld_imm64 with an address of bpf subprogram is a special instruction and proceeded to randomize it. By itself it wouldn't have been an issue, but jit_subprogs() logic relies on two step process to JIT all subprogs and then JIT them again when addresses of all subprogs are known. Blinding process in the first JIT phase caused second JIT to miss adjustment of special ld_imm64. Fix this issue by ignoring special ld_imm64 instructions that don't have user controlled constants and shouldn't be blinded.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: provide block_invalidate_folio to fix memory leak The ntfs3 filesystem lacks the 'invalidate_folio' method and it causes memory leak. If you write to the filesystem and then unmount it, the cached written data are not freed and they are permanently leaked.

In the Linux kernel, the following vulnerability has been resolved: x86/MCE/AMD: Fix memory leak when threshold_create_bank() fails In mce_threshold_create_device(), if threshold_create_bank() fails, the previously allocated threshold banks array @bp will be leaked because the call to mce_threshold_remove_device() will not free it. This happens because mce_threshold_remove_device() fetches the pointer through the threshold_banks per-CPU variable but bp is written there only after the bank creation is successful, and not before, when threshold_create_bank() fails. Add a helper which unwinds all the bank creation work previously done and pass into it the previously allocated threshold banks array for freeing. [ bp: Massage. ]

In the Linux kernel, the following vulnerability has been resolved: btrfs: fix deadlock between concurrent dio writes when low on free data space When reserving data space for a direct IO write we can end up deadlocking if we have multiple tasks attempting a write to the same file range, there are multiple extents covered by that file range, we are low on available space for data and the writes don't expand the inode's i_size. The deadlock can happen like this: 1) We have a file with an i_size of 1M, at offset 0 it has an extent with a size of 128K and at offset 128K it has another extent also with a size of 128K; 2) Task A does a direct IO write against file range [0, 256K), and because the write is within the i_size boundary, it takes the inode's lock (VFS level) in shared mode; 3) Task A locks the file range [0, 256K) at btrfs_dio_iomap_begin(), and then gets the extent map for the extent covering the range [0, 128K). At btrfs_get_blocks_direct_write(), it creates an ordered extent for that file range ([0, 128K)); 4) Before returning from btrfs_dio_iomap_begin(), it unlocks the file range [0, 256K); 5) Task A executes btrfs_dio_iomap_begin() again, this time for the file range [128K, 256K), and locks the file range [128K, 256K); 6) Task B starts a direct IO write against file range [0, 256K) as well. It also locks the inode in shared mode, as it's within the i_size limit, and then tries to lock file range [0, 256K). It is able to lock the subrange [0, 128K) but then blocks waiting for the range [128K, 256K), as it is currently locked by task A; 7) Task A enters btrfs_get_blocks_direct_write() and tries to reserve data space. Because we are low on available free space, it triggers the async data reclaim task, and waits for it to reserve data space; 8) The async reclaim task decides to wait for all existing ordered extents to complete (through btrfs_wait_ordered_roots()). It finds the ordered extent previously created by task A for the file range [0, 128K) and waits for it to complete; 9) The ordered extent for the file range [0, 128K) can not complete because it blocks at btrfs_finish_ordered_io() when trying to lock the file range [0, 128K). This results in a deadlock, because: - task B is holding the file range [0, 128K) locked, waiting for the range [128K, 256K) to be unlocked by task A; - task A is holding the file range [128K, 256K) locked and it's waiting for the async data reclaim task to satisfy its space reservation request; - the async data reclaim task is waiting for ordered extent [0, 128K) to complete, but the ordered extent can not complete because the file range [0, 128K) is currently locked by task B, which is waiting on task A to unlock file range [128K, 256K) and task A waiting on the async data reclaim task. This results in a deadlock between 4 task: task A, task B, the async data reclaim task and the task doing ordered extent completion (a work queue task). This type of deadlock can sporadically be triggered by the test case generic/300 from fstests, and results in a stack trace like the following: [12084.033689] INFO: task kworker/u16:7:123749 blocked for more than 241 seconds. [12084.034877] Not tainted 5.18.0-rc2-btrfs-next-115 #1 [12084.035562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [12084.036548] task:kworker/u16:7 state:D stack: 0 pid:123749 ppid: 2 flags:0x00004000 [12084.036554] Workqueue: btrfs-flush_delalloc btrfs_work_helper [btrfs] [12084.036599] Call Trace: [12084.036601] <TASK> [12084.036606] __schedule+0x3cb/0xed0 [12084.036616] schedule+0x4e/0xb0 [12084.036620] btrfs_start_ordered_extent+0x109/0x1c0 [btrfs] [12084.036651] ? prepare_to_wait_exclusive+0xc0/0xc0 [12084.036659] btrfs_run_ordered_extent_work+0x1a/0x30 [btrfs] [12084.036688] btrfs_work_helper+0xf8/0x400 [btrfs] [12084.0367 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: x86/kexec: fix memory leak of elf header buffer This is reported by kmemleak detector: unreferenced object 0xffffc900002a9000 (size 4096): comm "kexec", pid 14950, jiffies 4295110793 (age 373.951s) hex dump (first 32 bytes): 7f 45 4c 46 02 01 01 00 00 00 00 00 00 00 00 00 .ELF............ 04 00 3e 00 01 00 00 00 00 00 00 00 00 00 00 00 ..>............. backtrace: [<0000000016a8ef9f>] __vmalloc_node_range+0x101/0x170 [<000000002b66b6c0>] __vmalloc_node+0xb4/0x160 [<00000000ad40107d>] crash_prepare_elf64_headers+0x8e/0xcd0 [<0000000019afff23>] crash_load_segments+0x260/0x470 [<0000000019ebe95c>] bzImage64_load+0x814/0xad0 [<0000000093e16b05>] arch_kexec_kernel_image_load+0x1be/0x2a0 [<000000009ef2fc88>] kimage_file_alloc_init+0x2ec/0x5a0 [<0000000038f5a97a>] __do_sys_kexec_file_load+0x28d/0x530 [<0000000087c19992>] do_syscall_64+0x3b/0x90 [<0000000066e063a4>] entry_SYSCALL_64_after_hwframe+0x44/0xae In crash_prepare_elf64_headers(), a buffer is allocated via vmalloc() to store elf headers. While it's not freed back to system correctly when kdump kernel is reloaded or unloaded. Then memory leak is caused. Fix it by introducing x86 specific function arch_kimage_file_post_load_cleanup(), and freeing the buffer there. And also remove the incorrect elf header buffer freeing code. Before calling arch specific kexec_file loading function, the image instance has been initialized. So 'image->elf_headers' must be NULL. It doesn't make sense to free the elf header buffer in the place. Three different people have reported three bugs about the memory leak on x86_64 inside Redhat.

In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: Cancel pending work at closing a MIDI substream At closing a USB MIDI output substream, there might be still a pending work, which would eventually access the rawmidi runtime object that is being released. For fixing the race, make sure to cancel the pending work at closing.

In the Linux kernel, the following vulnerability has been resolved: ipw2x00: Fix potential NULL dereference in libipw_xmit() crypt and crypt->ops could be null, so we need to checking null before dereference

In the Linux kernel, the following vulnerability has been resolved: ath11k: fix the warning of dev_wake in mhi_pm_disable_transition() When test device recovery with below command, it has warning in message as below. echo assert > /sys/kernel/debug/ath11k/wcn6855\ hw2.0/simulate_fw_crash echo assert > /sys/kernel/debug/ath11k/qca6390\ hw2.0/simulate_fw_crash warning message: [ 1965.642121] ath11k_pci 0000:06:00.0: simulating firmware assert crash [ 1968.471364] ieee80211 phy0: Hardware restart was requested [ 1968.511305] ------------[ cut here ]------------ [ 1968.511368] WARNING: CPU: 3 PID: 1546 at drivers/bus/mhi/core/pm.c:505 mhi_pm_disable_transition+0xb37/0xda0 [mhi] [ 1968.511443] Modules linked in: ath11k_pci ath11k mac80211 libarc4 cfg80211 qmi_helpers qrtr_mhi mhi qrtr nvme nvme_core [ 1968.511563] CPU: 3 PID: 1546 Comm: kworker/u17:0 Kdump: loaded Tainted: G W 5.17.0-rc3-wt-ath+ #579 [ 1968.511629] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0067.2021.0528.1339 05/28/2021 [ 1968.511704] Workqueue: mhi_hiprio_wq mhi_pm_st_worker [mhi] [ 1968.511787] RIP: 0010:mhi_pm_disable_transition+0xb37/0xda0 [mhi] [ 1968.511870] Code: a9 fe ff ff 4c 89 ff 44 89 04 24 e8 03 46 f6 e5 44 8b 04 24 41 83 f8 01 0f 84 21 fe ff ff e9 4c fd ff ff 0f 0b e9 af f8 ff ff <0f> 0b e9 5c f8 ff ff 48 89 df e8 da 9e ee e3 e9 12 fd ff ff 4c 89 [ 1968.511923] RSP: 0018:ffffc900024efbf0 EFLAGS: 00010286 [ 1968.511969] RAX: 00000000ffffffff RBX: ffff88811d241250 RCX: ffffffffc0176922 [ 1968.512014] RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffff888118a90a24 [ 1968.512059] RBP: ffff888118a90800 R08: 0000000000000000 R09: ffff888118a90a27 [ 1968.512102] R10: ffffed1023152144 R11: 0000000000000001 R12: ffff888118a908ac [ 1968.512229] R13: ffff888118a90928 R14: dffffc0000000000 R15: ffff888118a90a24 [ 1968.512310] FS: 0000000000000000(0000) GS:ffff888234200000(0000) knlGS:0000000000000000 [ 1968.512405] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1968.512493] CR2: 00007f5538f443a8 CR3: 000000016dc28001 CR4: 00000000003706e0 [ 1968.512587] Call Trace: [ 1968.512672] <TASK> [ 1968.512751] ? _raw_spin_unlock_irq+0x1f/0x40 [ 1968.512859] mhi_pm_st_worker+0x3ac/0x790 [mhi] [ 1968.512959] ? mhi_pm_mission_mode_transition.isra.0+0x7d0/0x7d0 [mhi] [ 1968.513063] process_one_work+0x86a/0x1400 [ 1968.513184] ? pwq_dec_nr_in_flight+0x230/0x230 [ 1968.513312] ? move_linked_works+0x125/0x290 [ 1968.513416] worker_thread+0x6db/0xf60 [ 1968.513536] ? process_one_work+0x1400/0x1400 [ 1968.513627] kthread+0x241/0x2d0 [ 1968.513733] ? kthread_complete_and_exit+0x20/0x20 [ 1968.513821] ret_from_fork+0x22/0x30 [ 1968.513924] </TASK> Reason is mhi_deassert_dev_wake() from mhi_device_put() is called but mhi_assert_dev_wake() from __mhi_device_get_sync() is not called in progress of recovery. Commit 8e0559921f9a ("bus: mhi: core: Skip device wake in error or shutdown state") add check for the pm_state of mhi in __mhi_device_get_sync(), and the pm_state is not the normal state untill recovery is completed, so it leads the dev_wake is not 0 and above warning print in mhi_pm_disable_transition() while checking mhi_cntrl->dev_wake. Add check in ath11k_pci_write32()/ath11k_pci_read32() to skip call mhi_device_put() if mhi_device_get_sync() does not really do wake, then the warning gone. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Move cfg_log_verbose check before calling lpfc_dmp_dbg() In an attempt to log message 0126 with LOG_TRACE_EVENT, the following hard lockup call trace hangs the system. Call Trace: _raw_spin_lock_irqsave+0x32/0x40 lpfc_dmp_dbg.part.32+0x28/0x220 [lpfc] lpfc_cmpl_els_fdisc+0x145/0x460 [lpfc] lpfc_sli_cancel_jobs+0x92/0xd0 [lpfc] lpfc_els_flush_cmd+0x43c/0x670 [lpfc] lpfc_els_flush_all_cmd+0x37/0x60 [lpfc] lpfc_sli4_async_event_proc+0x956/0x1720 [lpfc] lpfc_do_work+0x1485/0x1d70 [lpfc] kthread+0x112/0x130 ret_from_fork+0x1f/0x40 Kernel panic - not syncing: Hard LOCKUP The same CPU tries to claim the phba->port_list_lock twice. Move the cfg_log_verbose checks as part of the lpfc_printf_vlog() and lpfc_printf_log() macros before calling lpfc_dmp_dbg(). There is no need to take the phba->port_list_lock within lpfc_dmp_dbg().

In the Linux kernel, the following vulnerability has been resolved: rcu-tasks: Fix race in schedule and flush work While booting secondary CPUs, cpus_read_[lock/unlock] is not keeping online cpumask stable. The transient online mask results in below calltrace. [ 0.324121] CPU1: Booted secondary processor 0x0000000001 [0x410fd083] [ 0.346652] Detected PIPT I-cache on CPU2 [ 0.347212] CPU2: Booted secondary processor 0x0000000002 [0x410fd083] [ 0.377255] Detected PIPT I-cache on CPU3 [ 0.377823] CPU3: Booted secondary processor 0x0000000003 [0x410fd083] [ 0.379040] ------------[ cut here ]------------ [ 0.383662] WARNING: CPU: 0 PID: 10 at kernel/workqueue.c:3084 __flush_work+0x12c/0x138 [ 0.384850] Modules linked in: [ 0.385403] CPU: 0 PID: 10 Comm: rcu_tasks_rude_ Not tainted 5.17.0-rc3-v8+ #13 [ 0.386473] Hardware name: Raspberry Pi 4 Model B Rev 1.4 (DT) [ 0.387289] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 0.388308] pc : __flush_work+0x12c/0x138 [ 0.388970] lr : __flush_work+0x80/0x138 [ 0.389620] sp : ffffffc00aaf3c60 [ 0.390139] x29: ffffffc00aaf3d20 x28: ffffffc009c16af0 x27: ffffff80f761df48 [ 0.391316] x26: 0000000000000004 x25: 0000000000000003 x24: 0000000000000100 [ 0.392493] x23: ffffffffffffffff x22: ffffffc009c16b10 x21: ffffffc009c16b28 [ 0.393668] x20: ffffffc009e53861 x19: ffffff80f77fbf40 x18: 00000000d744fcc9 [ 0.394842] x17: 000000000000000b x16: 00000000000001c2 x15: ffffffc009e57550 [ 0.396016] x14: 0000000000000000 x13: ffffffffffffffff x12: 0000000100000000 [ 0.397190] x11: 0000000000000462 x10: ffffff8040258008 x9 : 0000000100000000 [ 0.398364] x8 : 0000000000000000 x7 : ffffffc0093c8bf4 x6 : 0000000000000000 [ 0.399538] x5 : 0000000000000000 x4 : ffffffc00a976e40 x3 : ffffffc00810444c [ 0.400711] x2 : 0000000000000004 x1 : 0000000000000000 x0 : 0000000000000000 [ 0.401886] Call trace: [ 0.402309] __flush_work+0x12c/0x138 [ 0.402941] schedule_on_each_cpu+0x228/0x278 [ 0.403693] rcu_tasks_rude_wait_gp+0x130/0x144 [ 0.404502] rcu_tasks_kthread+0x220/0x254 [ 0.405264] kthread+0x174/0x1ac [ 0.405837] ret_from_fork+0x10/0x20 [ 0.406456] irq event stamp: 102 [ 0.406966] hardirqs last enabled at (101): [<ffffffc0093c8468>] _raw_spin_unlock_irq+0x78/0xb4 [ 0.408304] hardirqs last disabled at (102): [<ffffffc0093b8270>] el1_dbg+0x24/0x5c [ 0.409410] softirqs last enabled at (54): [<ffffffc0081b80c8>] local_bh_enable+0xc/0x2c [ 0.410645] softirqs last disabled at (50): [<ffffffc0081b809c>] local_bh_disable+0xc/0x2c [ 0.411890] ---[ end trace 0000000000000000 ]--- [ 0.413000] smp: Brought up 1 node, 4 CPUs [ 0.413762] SMP: Total of 4 processors activated. [ 0.414566] CPU features: detected: 32-bit EL0 Support [ 0.415414] CPU features: detected: 32-bit EL1 Support [ 0.416278] CPU features: detected: CRC32 instructions [ 0.447021] Callback from call_rcu_tasks_rude() invoked. [ 0.506693] Callback from call_rcu_tasks() invoked. This commit therefore fixes this issue by applying a single-CPU optimization to the RCU Tasks Rude grace-period process. The key point here is that the purpose of this RCU flavor is to force a schedule on each online CPU since some past event. But the rcu_tasks_rude_wait_gp() function runs in the context of the RCU Tasks Rude's grace-period kthread, so there must already have been a context switch on the current CPU since the call to either synchronize_rcu_tasks_rude() or call_rcu_tasks_rude(). So if there is only a single CPU online, RCU Tasks Rude's grace-period kthread does not need to anything at all. It turns out that the rcu_tasks_rude_wait_gp() function's call to schedule_on_each_cpu() causes problems during early boot. During that time, there is only one online CPU, namely the boot CPU. Therefore, applying this single-CPU optimization fixes early-boot instances of this problem.

In the Linux kernel, the following vulnerability has been resolved: rtw89: ser: fix CAM leaks occurring in L2 reset The CAM, meaning address CAM and bssid CAM here, will get leaks during SER (system error recover) L2 reset process and ieee80211_restart_hw() which is called by L2 reset process eventually. The normal flow would be like -> add interface (acquire 1) -> enter ips (release 1) -> leave ips (acquire 1) -> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection> The ieee80211_restart_hw() flow (under connection) -> ieee80211 reconfig -> add interface (acquire 1) -> leave ips (acquire 1) -> connection (occupy (A) + 2) <(B) 1 more leak> Originally, CAM is released before HW restart only if connection is under security. Now, release CAM whatever connection it is to fix leak in (A). OTOH, check if CAM is already valid to avoid acquiring multiple times to fix (B). Besides, if AP mode, release address CAM of all stations before HW restart.

In the Linux kernel, the following vulnerability has been resolved: ALSA: jack: Access input_dev under mutex It is possible when using ASoC that input_dev is unregistered while calling snd_jack_report, which causes NULL pointer dereference. In order to prevent this serialize access to input_dev using mutex lock.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix call trace observed during I/O with CMF enabled The following was seen with CMF enabled: BUG: using smp_processor_id() in preemptible code: systemd-udevd/31711 kernel: caller is lpfc_update_cmf_cmd+0x214/0x420 [lpfc] kernel: CPU: 12 PID: 31711 Comm: systemd-udevd kernel: Call Trace: kernel: <TASK> kernel: dump_stack_lvl+0x44/0x57 kernel: check_preemption_disabled+0xbf/0xe0 kernel: lpfc_update_cmf_cmd+0x214/0x420 [lpfc] kernel: lpfc_nvme_fcp_io_submit+0x23b4/0x4df0 [lpfc] this_cpu_ptr() calls smp_processor_id() in a preemptible context. Fix by using per_cpu_ptr() with raw_smp_processor_id() instead.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix SCSI I/O completion and abort handler deadlock During stress I/O tests with 500+ vports, hard LOCKUP call traces are observed. CPU A: native_queued_spin_lock_slowpath+0x192 _raw_spin_lock_irqsave+0x32 lpfc_handle_fcp_err+0x4c6 lpfc_fcp_io_cmd_wqe_cmpl+0x964 lpfc_sli4_fp_handle_cqe+0x266 __lpfc_sli4_process_cq+0x105 __lpfc_sli4_hba_process_cq+0x3c lpfc_cq_poll_hdler+0x16 irq_poll_softirq+0x76 __softirqentry_text_start+0xe4 irq_exit+0xf7 do_IRQ+0x7f CPU B: native_queued_spin_lock_slowpath+0x5b _raw_spin_lock+0x1c lpfc_abort_handler+0x13e scmd_eh_abort_handler+0x85 process_one_work+0x1a7 worker_thread+0x30 kthread+0x112 ret_from_fork+0x1f Diagram of lockup: CPUA CPUB ---- ---- lpfc_cmd->buf_lock phba->hbalock lpfc_cmd->buf_lock phba->hbalock Fix by reordering the taking of the lpfc_cmd->buf_lock and phba->hbalock in lpfc_abort_handler routine so that it tries to take the lpfc_cmd->buf_lock first before phba->hbalock.

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Protect memory leak for NPIV ports sending PLOGI_RJT There is a potential memory leak in lpfc_ignore_els_cmpl() and lpfc_els_rsp_reject() that was allocated from NPIV PLOGI_RJT (lpfc_rcv_plogi()'s login_mbox). Check if cmdiocb->context_un.mbox was allocated in lpfc_ignore_els_cmpl(), and then free it back to phba->mbox_mem_pool along with mbox->ctx_buf for service parameters. For lpfc_els_rsp_reject() failure, free both the ctx_buf for service parameters and the login_mbox.

In the Linux kernel, the following vulnerability has been resolved: ath11k: Change max no of active probe SSID and BSSID to fw capability The maximum number of SSIDs in a for active probe requests is currently reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver. The scan_req_params structure only has the capacity to hold 10 SSIDs. This leads to a buffer overflow which can be triggered from wpa_supplicant in userspace. When copying the SSIDs into the scan_req_params structure in the ath11k_mac_op_hw_scan route, it can overwrite the extraie pointer. Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe request will be sent, so totally 64 probe requests supported. So set both max ssid and bssid to 16 and 4 respectively. Remove the redundant macros of ssid and bssid. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: drm/virtio: fix NULL pointer dereference in virtio_gpu_conn_get_modes drm_cvt_mode may return NULL and we should check it. This bug is found by syzkaller: FAULT_INJECTION stacktrace: [ 168.567394] FAULT_INJECTION: forcing a failure. name failslab, interval 1, probability 0, space 0, times 1 [ 168.567403] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1 [ 168.567406] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 [ 168.567408] Call trace: [ 168.567414] dump_backtrace+0x0/0x310 [ 168.567418] show_stack+0x28/0x38 [ 168.567423] dump_stack+0xec/0x15c [ 168.567427] should_fail+0x3ac/0x3d0 [ 168.567437] __should_failslab+0xb8/0x120 [ 168.567441] should_failslab+0x28/0xc0 [ 168.567445] kmem_cache_alloc_trace+0x50/0x640 [ 168.567454] drm_mode_create+0x40/0x90 [ 168.567458] drm_cvt_mode+0x48/0xc78 [ 168.567477] virtio_gpu_conn_get_modes+0xa8/0x140 [virtio_gpu] [ 168.567485] drm_helper_probe_single_connector_modes+0x3a4/0xd80 [ 168.567492] drm_mode_getconnector+0x2e0/0xa70 [ 168.567496] drm_ioctl_kernel+0x11c/0x1d8 [ 168.567514] drm_ioctl+0x558/0x6d0 [ 168.567522] do_vfs_ioctl+0x160/0xf30 [ 168.567525] ksys_ioctl+0x98/0xd8 [ 168.567530] __arm64_sys_ioctl+0x50/0xc8 [ 168.567536] el0_svc_common+0xc8/0x320 [ 168.567540] el0_svc_handler+0xf8/0x160 [ 168.567544] el0_svc+0x10/0x218 KASAN stacktrace: [ 168.567561] BUG: KASAN: null-ptr-deref in virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu] [ 168.567565] Read of size 4 at addr 0000000000000054 by task syz/6425 [ 168.567566] [ 168.567571] CPU: 1 PID: 6425 Comm: syz Kdump: loaded Not tainted 4.19.90-vhulk2201.1.0.h1035.kasan.eulerosv2r10.aarch64 #1 [ 168.567573] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015 [ 168.567575] Call trace: [ 168.567578] dump_backtrace+0x0/0x310 [ 168.567582] show_stack+0x28/0x38 [ 168.567586] dump_stack+0xec/0x15c [ 168.567591] kasan_report+0x244/0x2f0 [ 168.567594] __asan_load4+0x58/0xb0 [ 168.567607] virtio_gpu_conn_get_modes+0xb4/0x140 [virtio_gpu] [ 168.567612] drm_helper_probe_single_connector_modes+0x3a4/0xd80 [ 168.567617] drm_mode_getconnector+0x2e0/0xa70 [ 168.567621] drm_ioctl_kernel+0x11c/0x1d8 [ 168.567624] drm_ioctl+0x558/0x6d0 [ 168.567628] do_vfs_ioctl+0x160/0xf30 [ 168.567632] ksys_ioctl+0x98/0xd8 [ 168.567636] __arm64_sys_ioctl+0x50/0xc8 [ 168.567641] el0_svc_common+0xc8/0x320 [ 168.567645] el0_svc_handler+0xf8/0x160 [ 168.567649] el0_svc+0x10/0x218

In the Linux kernel, the following vulnerability has been resolved: loop: implement ->free_disk Ensure that the lo_device which is stored in the gendisk private data is valid until the gendisk is freed. Currently the loop driver uses a lot of effort to make sure a device is not freed when it is still in use, but to to fix a potential deadlock this will be relaxed a bit soon.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu/pm: fix the null pointer while the smu is disabled It needs to check if the pp_funcs is initialized while release the context, otherwise it will trigger null pointer panic while the software smu is not enabled. [ 1109.404555] BUG: kernel NULL pointer dereference, address: 0000000000000078 [ 1109.404609] #PF: supervisor read access in kernel mode [ 1109.404638] #PF: error_code(0x0000) - not-present page [ 1109.404657] PGD 0 P4D 0 [ 1109.404672] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 1109.404701] CPU: 7 PID: 9150 Comm: amdgpu_test Tainted: G OEL 5.16.0-custom #1 [ 1109.404732] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 1109.404765] RIP: 0010:amdgpu_dpm_force_performance_level+0x1d/0x170 [amdgpu] [ 1109.405109] Code: 5d c3 44 8b a3 f0 80 00 00 eb e5 66 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 41 54 53 48 83 ec 08 4c 8b b7 f0 7d 00 00 <49> 83 7e 78 00 0f 84 f2 00 00 00 80 bf 87 80 00 00 00 48 89 fb 0f [ 1109.405176] RSP: 0018:ffffaf3083ad7c20 EFLAGS: 00010282 [ 1109.405203] RAX: 0000000000000000 RBX: ffff9796b1c14600 RCX: 0000000002862007 [ 1109.405229] RDX: ffff97968591c8c0 RSI: 0000000000000001 RDI: ffff9796a3700000 [ 1109.405260] RBP: ffffaf3083ad7c50 R08: ffffffff9897de00 R09: ffff979688d9db60 [ 1109.405286] R10: 0000000000000000 R11: ffff979688d9db90 R12: 0000000000000001 [ 1109.405316] R13: ffff9796a3700000 R14: 0000000000000000 R15: ffff9796a3708fc0 [ 1109.405345] FS: 00007ff055cff180(0000) GS:ffff9796bfdc0000(0000) knlGS:0000000000000000 [ 1109.405378] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1109.405400] CR2: 0000000000000078 CR3: 000000000a394000 CR4: 00000000000506e0 [ 1109.405434] Call Trace: [ 1109.405445] <TASK> [ 1109.405456] ? delete_object_full+0x1d/0x20 [ 1109.405480] amdgpu_ctx_set_stable_pstate+0x7c/0xa0 [amdgpu] [ 1109.405698] amdgpu_ctx_fini.part.0+0xcb/0x100 [amdgpu] [ 1109.405911] amdgpu_ctx_do_release+0x71/0x80 [amdgpu] [ 1109.406121] amdgpu_ctx_ioctl+0x52d/0x550 [amdgpu] [ 1109.406327] ? _raw_spin_unlock+0x1a/0x30 [ 1109.406354] ? drm_gem_handle_delete+0x81/0xb0 [drm] [ 1109.406400] ? amdgpu_ctx_get_entity+0x2c0/0x2c0 [amdgpu] [ 1109.406609] drm_ioctl_kernel+0xb6/0x140 [drm]

In the Linux kernel, the following vulnerability has been resolved: media: i2c: dw9714: Disable the regulator when the driver fails to probe When the driver fails to probe, we will get the following splat: [ 59.305988] ------------[ cut here ]------------ [ 59.306417] WARNING: CPU: 2 PID: 395 at drivers/regulator/core.c:2257 _regulator_put+0x3ec/0x4e0 [ 59.310345] RIP: 0010:_regulator_put+0x3ec/0x4e0 [ 59.318362] Call Trace: [ 59.318582] <TASK> [ 59.318765] regulator_put+0x1f/0x30 [ 59.319058] devres_release_group+0x319/0x3d0 [ 59.319420] i2c_device_probe+0x766/0x940 Fix this by disabling the regulator in error handling.

In the Linux kernel, the following vulnerability has been resolved: media: venus: hfi: avoid null dereference in deinit If venus_probe fails at pm_runtime_put_sync the error handling first calls hfi_destroy and afterwards hfi_core_deinit. As hfi_destroy sets core->ops to NULL, hfi_core_deinit cannot call the core_deinit function anymore. Avoid this null pointer derefence by skipping the call when necessary.

In the Linux kernel, the following vulnerability has been resolved: md/bitmap: don't set sb values if can't pass sanity check If bitmap area contains invalid data, kernel will crash then mdadm triggers "Segmentation fault". This is cluster-md speical bug. In non-clustered env, mdadm will handle broken metadata case. In clustered array, only kernel space handles bitmap slot info. But even this bug only happened in clustered env, current sanity check is wrong, the code should be changed. How to trigger: (faulty injection) dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sda dd if=/dev/zero bs=1M count=1 oflag=direct of=/dev/sdb mdadm -C /dev/md0 -b clustered -e 1.2 -n 2 -l mirror /dev/sda /dev/sdb mdadm -Ss echo aaa > magic.txt == below modifying slot 2 bitmap data == dd if=magic.txt of=/dev/sda seek=16384 bs=1 count=3 <== destroy magic dd if=/dev/zero of=/dev/sda seek=16436 bs=1 count=4 <== ZERO chunksize mdadm -A /dev/md0 /dev/sda /dev/sdb == kernel crashes. mdadm outputs "Segmentation fault" == Reason of kernel crash: In md_bitmap_read_sb (called by md_bitmap_create), bad bitmap magic didn't block chunksize assignment, and zero value made DIV_ROUND_UP_SECTOR_T() trigger "divide error". Crash log: kernel: md: md0 stopped. kernel: md/raid1:md0: not clean -- starting background reconstruction kernel: md/raid1:md0: active with 2 out of 2 mirrors kernel: dlm: ... ... kernel: md-cluster: Joined cluster 44810aba-38bb-e6b8-daca-bc97a0b254aa slot 1 kernel: md0: invalid bitmap file superblock: bad magic kernel: md_bitmap_copy_from_slot can't get bitmap from slot 2 kernel: md-cluster: Could not gather bitmaps from slot 2 kernel: divide error: 0000 [#1] SMP NOPTI kernel: CPU: 0 PID: 1603 Comm: mdadm Not tainted 5.14.6-1-default kernel: Hardware name: QEMU Standard PC (i440FX + PIIX, 1996) kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod] kernel: RSP: 0018:ffffc22ac0843ba0 EFLAGS: 00010246 kernel: ... ... kernel: Call Trace: kernel: ? dlm_lock_sync+0xd0/0xd0 [md_cluster 77fe..7a0] kernel: md_bitmap_copy_from_slot+0x2c/0x290 [md_mod 24ea..d3a] kernel: load_bitmaps+0xec/0x210 [md_cluster 77fe..7a0] kernel: md_bitmap_load+0x81/0x1e0 [md_mod 24ea..d3a] kernel: do_md_run+0x30/0x100 [md_mod 24ea..d3a] kernel: md_ioctl+0x1290/0x15a0 [md_mod 24ea....d3a] kernel: ? mddev_unlock+0xaa/0x130 [md_mod 24ea..d3a] kernel: ? blkdev_ioctl+0xb1/0x2b0 kernel: block_ioctl+0x3b/0x40 kernel: __x64_sys_ioctl+0x7f/0xb0 kernel: do_syscall_64+0x59/0x80 kernel: ? exit_to_user_mode_prepare+0x1ab/0x230 kernel: ? syscall_exit_to_user_mode+0x18/0x40 kernel: ? do_syscall_64+0x69/0x80 kernel: entry_SYSCALL_64_after_hwframe+0x44/0xae kernel: RIP: 0033:0x7f4a15fa722b kernel: ... ... kernel: ---[ end trace 8afa7612f559c868 ]--- kernel: RIP: 0010:md_bitmap_create+0x1d1/0x850 [md_mod]

In the Linux kernel, the following vulnerability has been resolved: media: cx25821: Fix the warning when removing the module When removing the module, we will get the following warning: [ 14.746697] remove_proc_entry: removing non-empty directory 'irq/21', leaking at least 'cx25821[1]' [ 14.747449] WARNING: CPU: 4 PID: 368 at fs/proc/generic.c:717 remove_proc_entry+0x389/0x3f0 [ 14.751611] RIP: 0010:remove_proc_entry+0x389/0x3f0 [ 14.759589] Call Trace: [ 14.759792] <TASK> [ 14.759975] unregister_irq_proc+0x14c/0x170 [ 14.760340] irq_free_descs+0x94/0xe0 [ 14.760640] mp_unmap_irq+0xb6/0x100 [ 14.760937] acpi_unregister_gsi_ioapic+0x27/0x40 [ 14.761334] acpi_pci_irq_disable+0x1d3/0x320 [ 14.761688] pci_disable_device+0x1ad/0x380 [ 14.762027] ? _raw_spin_unlock_irqrestore+0x2d/0x60 [ 14.762442] ? cx25821_shutdown+0x20/0x9f0 [cx25821] [ 14.762848] cx25821_finidev+0x48/0xc0 [cx25821] [ 14.763242] pci_device_remove+0x92/0x240 Fix this by freeing the irq before call pci_disable_device().

In the Linux kernel, the following vulnerability has been resolved: ath11k: disable spectral scan during spectral deinit When ath11k modules are removed using rmmod with spectral scan enabled, crash is observed. Different crash trace is observed for each crash. Send spectral scan disable WMI command to firmware before cleaning the spectral dbring in the spectral_deinit API to avoid this crash. call trace from one of the crash observed: [ 1252.880802] Unable to handle kernel NULL pointer dereference at virtual address 00000008 [ 1252.882722] pgd = 0f42e886 [ 1252.890955] [00000008] *pgd=00000000 [ 1252.893478] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 1253.093035] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.89 #0 [ 1253.115261] Hardware name: Generic DT based system [ 1253.121149] PC is at ath11k_spectral_process_data+0x434/0x574 [ath11k] [ 1253.125940] LR is at 0x88e31017 [ 1253.132448] pc : [<7f9387b8>] lr : [<88e31017>] psr: a0000193 [ 1253.135488] sp : 80d01bc8 ip : 00000001 fp : 970e0000 [ 1253.141737] r10: 88e31000 r9 : 970ec000 r8 : 00000080 [ 1253.146946] r7 : 94734040 r6 : a0000113 r5 : 00000057 r4 : 00000000 [ 1253.152159] r3 : e18cb694 r2 : 00000217 r1 : 1df1f000 r0 : 00000001 [ 1253.158755] Flags: NzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user [ 1253.165266] Control: 10c0383d Table: 5e71006a DAC: 00000055 [ 1253.172472] Process swapper/0 (pid: 0, stack limit = 0x60870141) [ 1253.458055] [<7f9387b8>] (ath11k_spectral_process_data [ath11k]) from [<7f917fdc>] (ath11k_dbring_buffer_release_event+0x214/0x2e4 [ath11k]) [ 1253.466139] [<7f917fdc>] (ath11k_dbring_buffer_release_event [ath11k]) from [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx+0x1840/0x29cc [ath11k]) [ 1253.478807] [<7f8ea3c4>] (ath11k_wmi_tlv_op_rx [ath11k]) from [<7f8fe868>] (ath11k_htc_rx_completion_handler+0x180/0x4e0 [ath11k]) [ 1253.490699] [<7f8fe868>] (ath11k_htc_rx_completion_handler [ath11k]) from [<7f91308c>] (ath11k_ce_per_engine_service+0x2c4/0x3b4 [ath11k]) [ 1253.502386] [<7f91308c>] (ath11k_ce_per_engine_service [ath11k]) from [<7f9a4198>] (ath11k_pci_ce_tasklet+0x28/0x80 [ath11k_pci]) [ 1253.514811] [<7f9a4198>] (ath11k_pci_ce_tasklet [ath11k_pci]) from [<8032227c>] (tasklet_action_common.constprop.2+0x64/0xe8) [ 1253.526476] [<8032227c>] (tasklet_action_common.constprop.2) from [<803021e8>] (__do_softirq+0x130/0x2d0) [ 1253.537756] [<803021e8>] (__do_softirq) from [<80322610>] (irq_exit+0xcc/0xe8) [ 1253.547304] [<80322610>] (irq_exit) from [<8036a4a4>] (__handle_domain_irq+0x60/0xb4) [ 1253.554428] [<8036a4a4>] (__handle_domain_irq) from [<805eb348>] (gic_handle_irq+0x4c/0x90) [ 1253.562321] [<805eb348>] (gic_handle_irq) from [<80301a78>] (__irq_svc+0x58/0x8c) Tested-on: QCN6122 hw1.0 AHB WLAN.HK.2.6.0.1-00851-QCAHKSWPL_SILICONZ-1

In the Linux kernel, the following vulnerability has been resolved: mmc: jz4740: Apply DMA engine limits to maximum segment size Do what is done in other DMA-enabled MMC host drivers (cf. host/mmci.c) and limit the maximum segment size based on the DMA engine's capabilities. This is needed to avoid warnings like the following with CONFIG_DMA_API_DEBUG=y. ------------[ cut here ]------------ WARNING: CPU: 0 PID: 21 at kernel/dma/debug.c:1162 debug_dma_map_sg+0x2f4/0x39c DMA-API: jz4780-dma 13420000.dma-controller: mapping sg segment longer than device claims to support [len=98304] [max=65536] CPU: 0 PID: 21 Comm: kworker/0:1H Not tainted 5.18.0-rc1 #19 Workqueue: kblockd blk_mq_run_work_fn Stack : 81575aec 00000004 80620000 80620000 80620000 805e7358 00000009 801537ac 814c832c 806276e3 806e34b4 80620000 81575aec 00000001 81575ab8 09291444 00000000 00000000 805e7358 81575958 ffffffea 8157596c 00000000 636f6c62 6220646b 80387a70 0000000f 6d5f6b6c 80620000 00000000 81575ba4 00000009 805e170c 80896640 00000001 00010000 00000000 00000000 00006098 806e0000 ... Call Trace: [<80107670>] show_stack+0x84/0x120 [<80528cd8>] __warn+0xb8/0xec [<80528d78>] warn_slowpath_fmt+0x6c/0xb8 [<8016f1d4>] debug_dma_map_sg+0x2f4/0x39c [<80169d4c>] __dma_map_sg_attrs+0xf0/0x118 [<8016a27c>] dma_map_sg_attrs+0x14/0x28 [<804f66b4>] jz4740_mmc_prepare_dma_data+0x74/0xa4 [<804f6714>] jz4740_mmc_pre_request+0x30/0x54 [<804f4ff4>] mmc_blk_mq_issue_rq+0x6e0/0x7bc [<804f5590>] mmc_mq_queue_rq+0x220/0x2d4 [<8038b2c0>] blk_mq_dispatch_rq_list+0x480/0x664 [<80391040>] blk_mq_do_dispatch_sched+0x2dc/0x370 [<80391468>] __blk_mq_sched_dispatch_requests+0xec/0x164 [<80391540>] blk_mq_sched_dispatch_requests+0x44/0x94 [<80387900>] __blk_mq_run_hw_queue+0xb0/0xcc [<80134c14>] process_one_work+0x1b8/0x264 [<80134ff8>] worker_thread+0x2ec/0x3b8 [<8013b13c>] kthread+0x104/0x10c [<80101dcc>] ret_from_kernel_thread+0x14/0x1c ---[ end trace 0000000000000000 ]---

In the Linux kernel, the following vulnerability has been resolved: scsi: lpfc: Fix resource leak in lpfc_sli4_send_seq_to_ulp() If no handler is found in lpfc_complete_unsol_iocb() to match the rctl of a received frame, the frame is dropped and resources are leaked. Fix by returning resources when discarding an unhandled frame type. Update lpfc_fc_frame_check() handling of NOP basic link service.

In the Linux kernel, the following vulnerability has been resolved: arm64: compat: Do not treat syscall number as ESR_ELx for a bad syscall If a compat process tries to execute an unknown system call above the __ARM_NR_COMPAT_END number, the kernel sends a SIGILL signal to the offending process. Information about the error is printed to dmesg in compat_arm_syscall() -> arm64_notify_die() -> arm64_force_sig_fault() -> arm64_show_signal(). arm64_show_signal() interprets a non-zero value for current->thread.fault_code as an exception syndrome and displays the message associated with the ESR_ELx.EC field (bits 31:26). current->thread.fault_code is set in compat_arm_syscall() -> arm64_notify_die() with the bad syscall number instead of a valid ESR_ELx value. This means that the ESR_ELx.EC field has the value that the user set for the syscall number and the kernel can end up printing bogus exception messages*. For example, for the syscall number 0x68000000, which evaluates to ESR_ELx.EC value of 0x1A (ESR_ELx_EC_FPAC) the kernel prints this error: [ 18.349161] syscall[300]: unhandled exception: ERET/ERETAA/ERETAB, ESR 0x68000000, Oops - bad compat syscall(2) in syscall[10000+50000] [ 18.350639] CPU: 2 PID: 300 Comm: syscall Not tainted 5.18.0-rc1 #79 [ 18.351249] Hardware name: Pine64 RockPro64 v2.0 (DT) [..] which is misleading, as the bad compat syscall has nothing to do with pointer authentication. Stop arm64_show_signal() from printing exception syndrome information by having compat_arm_syscall() set the ESR_ELx value to 0, as it has no meaning for an invalid system call number. The example above now becomes: [ 19.935275] syscall[301]: unhandled exception: Oops - bad compat syscall(2) in syscall[10000+50000] [ 19.936124] CPU: 1 PID: 301 Comm: syscall Not tainted 5.18.0-rc1-00005-g7e08006d4102 #80 [ 19.936894] Hardware name: Pine64 RockPro64 v2.0 (DT) [..] which although shows less information because the syscall number, wrongfully advertised as the ESR value, is missing, it is better than showing plainly wrong information. The syscall number can be easily obtained with strace. *A 32-bit value above or equal to 0x8000_0000 is interpreted as a negative integer in compat_arm_syscal() and the condition scno < __ARM_NR_COMPAT_END evaluates to true; the syscall will exit to userspace in this case with the ENOSYS error code instead of arm64_notify_die() being called.

In the Linux kernel, the following vulnerability has been resolved: ASoC: mediatek: Fix missing of_node_put in mt2701_wm8960_machine_probe This node pointer is returned by of_parse_phandle() with refcount incremented in this function. Calling of_node_put() to avoid the refcount leak.

In the Linux kernel, the following vulnerability has been resolved: ice: always check VF VSI pointer values The ice_get_vf_vsi function can return NULL in some cases, such as if handling messages during a reset where the VSI is being removed and recreated. Several places throughout the driver do not bother to check whether this VSI pointer is valid. Static analysis tools maybe report issues because they detect paths where a potentially NULL pointer could be dereferenced. Fix this by checking the return value of ice_get_vf_vsi everywhere.