CVE Database

In the Linux kernel, the following vulnerability has been resolved: mlxbf-bootctl: use sysfs_emit_at() in secure_boot_fuse_state_show() A warning is seen when running the latest kernel on a BlueField SOC: [251.512704] ------------[ cut here ]------------ [251.512711] invalid sysfs_emit: buf:0000000003aa32ae [251.512720] WARNING: CPU: 1 PID: 705264 at fs/sysfs/file.c:767 sysfs_emit+0xac/0xc8 The warning is triggered because the mlxbf-bootctl driver invokes "sysfs_emit()" with a buffer pointer that is not aligned to the start of the page. The driver should instead use "sysfs_emit_at()" to support non-zero offsets into the destination buffer.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: mv88e6xxx: fix -ENOENT when deleting VLANs and MST is unsupported Russell King reports that on the ZII dev rev B, deleting a bridge VLAN from a user port fails with -ENOENT: https://lore.kernel.org/netdev/Z_lQXNP0s5-IiJzd@shell.armlinux.org.uk/ This comes from mv88e6xxx_port_vlan_leave() -> mv88e6xxx_mst_put(), which tries to find an MST entry in &chip->msts associated with the SID, but fails and returns -ENOENT as such. But we know that this chip does not support MST at all, so that is not surprising. The question is why does the guard in mv88e6xxx_mst_put() not exit early: if (!sid) return 0; And the answer seems to be simple: the sid comes from vlan.sid which supposedly was previously populated by mv88e6xxx_vtu_get(). But some chip->info->ops->vtu_getnext() implementations do not populate vlan.sid, for example see mv88e6185_g1_vtu_getnext(). In that case, later in mv88e6xxx_port_vlan_leave() we are using a garbage sid which is just residual stack memory. Testing for sid == 0 covers all cases of a non-bridge VLAN or a bridge VLAN mapped to the default MSTI. For some chips, SID 0 is valid and installed by mv88e6xxx_stu_setup(). A chip which does not support the STU would implicitly only support mapping all VLANs to the default MSTI, so although SID 0 is not valid, it would be sufficient, if we were to zero-initialize the vlan structure, to fix the bug, due to the coincidence that a test for vlan.sid == 0 already exists and leads to the same (correct) behavior. Another option which would be sufficient would be to add a test for mv88e6xxx_has_stu() inside mv88e6xxx_mst_put(), symmetric to the one which already exists in mv88e6xxx_mst_get(). But that placement means the caller will have to dereference vlan.sid, which means it will access uninitialized memory, which is not nice even if it ignores it later. So we end up making both modifications, in order to not rely just on the sid == 0 coincidence, but also to avoid having uninitialized structure fields which might get temporarily accessed.

In the Linux kernel, the following vulnerability has been resolved: net: dsa: clean up FDB, MDB, VLAN entries on unbind As explained in many places such as commit b117e1e8a86d ("net: dsa: delete dsa_legacy_fdb_add and dsa_legacy_fdb_del"), DSA is written given the assumption that higher layers have balanced additions/deletions. As such, it only makes sense to be extremely vocal when those assumptions are violated and the driver unbinds with entries still present. But Ido Schimmel points out a very simple situation where that is wrong: https://lore.kernel.org/netdev/ZDazSM5UsPPjQuKr@shredder/ (also briefly discussed by me in the aforementioned commit). Basically, while the bridge bypass operations are not something that DSA explicitly documents, and for the majority of DSA drivers this API simply causes them to go to promiscuous mode, that isn't the case for all drivers. Some have the necessary requirements for bridge bypass operations to do something useful - see dsa_switch_supports_uc_filtering(). Although in tools/testing/selftests/net/forwarding/local_termination.sh, we made an effort to popularize better mechanisms to manage address filters on DSA interfaces from user space - namely macvlan for unicast, and setsockopt(IP_ADD_MEMBERSHIP) - through mtools - for multicast, the fact is that 'bridge fdb add ... self static local' also exists as kernel UAPI, and might be useful to someone, even if only for a quick hack. It seems counter-productive to block that path by implementing shim .ndo_fdb_add and .ndo_fdb_del operations which just return -EOPNOTSUPP in order to prevent the ndo_dflt_fdb_add() and ndo_dflt_fdb_del() from running, although we could do that. Accepting that cleanup is necessary seems to be the only option. Especially since we appear to be coming back at this from a different angle as well. Russell King is noticing that the WARN_ON() triggers even for VLANs: https://lore.kernel.org/netdev/Z_li8Bj8bD4-BYKQ@shell.armlinux.org.uk/ What happens in the bug report above is that dsa_port_do_vlan_del() fails, then the VLAN entry lingers on, and then we warn on unbind and leak it. This is not a straight revert of the blamed commit, but we now add an informational print to the kernel log (to still have a way to see that bugs exist), and some extra comments gathered from past years' experience, to justify the logic.

In the Linux kernel, the following vulnerability has been resolved: ovl: don't allow datadir only In theory overlayfs could support upper layer directly referring to a data layer, but there's no current use case for this. Originally, when data-only layers were introduced, this wasn't allowed, only introduced by the "datadir+" feature, but without actually handling this case, resulting in an Oops. Fix by disallowing datadir without lowerdir.

In the Linux kernel, the following vulnerability has been resolved: HID: pidff: Fix null pointer dereference in pidff_find_fields This function triggered a null pointer dereference if used to search for a report that isn't implemented on the device. This happened both for optional and required reports alike. The same logic was applied to pidff_find_special_field and although pidff_init_fields should return an error earlier if one of the required reports is missing, future modifications could change this logic and resurface this possible null pointer dereference again. LKML bug report: https://lore.kernel.org/all/CAL-gK7f5=R0nrrQdPtaZZr1fd-cdAMbDMuZ_NLA8vM0SX+nGSw@mail.gmail.com

In the Linux kernel, the following vulnerability has been resolved: page_pool: avoid infinite loop to schedule delayed worker We noticed the kworker in page_pool_release_retry() was waken up repeatedly and infinitely in production because of the buggy driver causing the inflight less than 0 and warning us in page_pool_inflight()[1]. Since the inflight value goes negative, it means we should not expect the whole page_pool to get back to work normally. This patch mitigates the adverse effect by not rescheduling the kworker when detecting the inflight negative in page_pool_release_retry(). [1] [Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------ [Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages ... [Mon Feb 10 20:36:11 2025] Call Trace: [Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70 [Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370 [Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0 [Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140 [Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370 [Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40 [Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40 [Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]--- Note: before this patch, the above calltrace would flood the dmesg due to repeated reschedule of release_dw kworker.

In the Linux kernel, the following vulnerability has been resolved: fs/jfs: Prevent integer overflow in AG size calculation The JFS filesystem calculates allocation group (AG) size using 1 << l2agsize in dbExtendFS(). When l2agsize exceeds 31 (possible with >2TB aggregates on 32-bit systems), this 32-bit shift operation causes undefined behavior and improper AG sizing. On 32-bit architectures: - Left-shifting 1 by 32+ bits results in 0 due to integer overflow - This creates invalid AG sizes (0 or garbage values) in sbi->bmap->db_agsize - Subsequent block allocations would reference invalid AG structures - Could lead to: - Filesystem corruption during extend operations - Kernel crashes due to invalid memory accesses - Security vulnerabilities via malformed on-disk structures Fix by casting to s64 before shifting: bmp->db_agsize = (s64)1 << l2agsize; This ensures 64-bit arithmetic even on 32-bit architectures. The cast matches the data type of db_agsize (s64) and follows similar patterns in JFS block calculation code. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: scsi: st: Fix array overflow in st_setup() Change the array size to follow parms size instead of a fixed value.

In the Linux kernel, the following vulnerability has been resolved: btrfs: harden block_group::bg_list against list_del() races As far as I can tell, these calls of list_del_init() on bg_list cannot run concurrently with btrfs_mark_bg_unused() or btrfs_mark_bg_to_reclaim(), as they are in transaction error paths and situations where the block group is readonly. However, if there is any chance at all of racing with mark_bg_unused(), or a different future user of bg_list, better to be safe than sorry. Otherwise we risk the following interleaving (bg_list refcount in parens) T1 (some random op) T2 (btrfs_mark_bg_unused) !list_empty(&bg->bg_list); (1) list_del_init(&bg->bg_list); (1) list_move_tail (1) btrfs_put_block_group (0) btrfs_delete_unused_bgs bg = list_first_entry list_del_init(&bg->bg_list); btrfs_put_block_group(bg); (-1) Ultimately, this results in a broken ref count that hits zero one deref early and the real final deref underflows the refcount, resulting in a WARNING.

In the Linux kernel, the following vulnerability has been resolved: drm/amd/display: Guard Possible Null Pointer Dereference [WHY] In some situations, dc->res_pool may be null. [HOW] Check if pointer is null before dereference.

In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: debugfs hang_hws skip GPU with MES debugfs hang_hws is used by GPU reset test with HWS, for MES this crash the kernel with NULL pointer access because dqm->packet_mgr is not setup for MES path. Skip GPU with MES for now, MES hang_hws debugfs interface will be supported later.

In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: handle amdgpu_cgs_create_device() errors in amd_powerplay_create() Add error handling to propagate amdgpu_cgs_create_device() failures to the caller. When amdgpu_cgs_create_device() fails, release hwmgr and return -ENOMEM to prevent null pointer dereference. [v1]->[v2]: Change error code from -EINVAL to -ENOMEM. Free hwmgr.

In the Linux kernel, the following vulnerability has been resolved: fbdev: omapfb: Add 'plane' value check Function dispc_ovl_setup is not intended to work with the value OMAP_DSS_WB of the enum parameter plane. The value of this parameter is initialized in dss_init_overlays and in the current state of the code it cannot take this value so it's not a real problem. For the purposes of defensive coding it wouldn't be superfluous to check the parameter value, because some functions down the call stack process this value correctly and some not. For example, in dispc_ovl_setup_global_alpha it may lead to buffer overflow. Add check for this value. Found by Linux Verification Center (linuxtesting.org) with SVACE static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: pwm: mediatek: Prevent divide-by-zero in pwm_mediatek_config() With CONFIG_COMPILE_TEST && !CONFIG_HAVE_CLK, pwm_mediatek_config() has a divide-by-zero in the following line: do_div(resolution, clk_get_rate(pc->clk_pwms[pwm->hwpwm])); due to the fact that the !CONFIG_HAVE_CLK version of clk_get_rate() returns zero. This is presumably just a theoretical problem: COMPILE_TEST overrides the dependency on RALINK which would select COMMON_CLK. Regardless it's a good idea to check for the error explicitly to avoid divide-by-zero. Fixes the following warning: drivers/pwm/pwm-mediatek.o: warning: objtool: .text: unexpected end of section [ukleinek: s/CONFIG_CLK/CONFIG_HAVE_CLK/]

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix PM related deadlocks in MS IOCTLs Prevent runtime resume/suspend while MS IOCTLs are in progress. Failed suspend will call ivpu_ms_cleanup() that would try to acquire file_priv->ms_lock, which is already held by the IOCTLs.

In the Linux kernel, the following vulnerability has been resolved: accel/ivpu: Fix deadlock in ivpu_ms_cleanup() Fix deadlock in ivpu_ms_cleanup() by preventing runtime resume after file_priv->ms_lock is acquired. During a failure in runtime resume, a cold boot is executed, which calls ivpu_ms_cleanup_all(). This function calls ivpu_ms_cleanup() that acquires file_priv->ms_lock and causes the deadlock.

In the Linux kernel, the following vulnerability has been resolved: cifs: avoid NULL pointer dereference in dbg call cifs_server_dbg() implies server to be non-NULL so move call under condition to avoid NULL pointer dereference. Found by Linux Verification Center (linuxtesting.org) with SVACE.

In the Linux kernel, the following vulnerability has been resolved: PCI: pciehp: Avoid unnecessary device replacement check Hot-removal of nested PCI hotplug ports suffers from a long-standing race condition which can lead to a deadlock: A parent hotplug port acquires pci_lock_rescan_remove(), then waits for pciehp to unbind from a child hotplug port. Meanwhile that child hotplug port tries to acquire pci_lock_rescan_remove() as well in order to remove its own children. The deadlock only occurs if the parent acquires pci_lock_rescan_remove() first, not if the child happens to acquire it first. Several workarounds to avoid the issue have been proposed and discarded over the years, e.g.: https://lore.kernel.org/r/4c882e25194ba8282b78fe963fec8faae7cf23eb.1529173804.git.lukas@wunner.de/ A proper fix is being worked on, but needs more time as it is nontrivial and necessarily intrusive. Recent commit 9d573d19547b ("PCI: pciehp: Detect device replacement during system sleep") provokes more frequent occurrence of the deadlock when removing more than one Thunderbolt device during system sleep. The commit sought to detect device replacement, but also triggered on device removal. Differentiating reliably between replacement and removal is impossible because pci_get_dsn() returns 0 both if the device was removed, as well as if it was replaced with one lacking a Device Serial Number. Avoid the more frequent occurrence of the deadlock by checking whether the hotplug port itself was hot-removed. If so, there's no sense in checking whether its child device was replaced. This works because the ->resume_noirq() callback is invoked in top-down order for the entire hierarchy: A parent hotplug port detecting device replacement (or removal) marks all children as removed using pci_dev_set_disconnected() and a child hotplug port can then reliably detect being removed.

In the Linux kernel, the following vulnerability has been resolved: spi: fsl-qspi: use devm function instead of driver remove Driver use devm APIs to manage clk/irq/resources and register the spi controller, but the legacy remove function will be called first during device detach and trigger kernel panic. Drop the remove function and use devm_add_action_or_reset() for driver cleanup to ensure the release sequence. Trigger kernel panic on i.MX8MQ by echo 30bb0000.spi >/sys/bus/platform/drivers/fsl-quadspi/unbind

In the Linux kernel, the following vulnerability has been resolved: pm: cpupower: bench: Prevent NULL dereference on malloc failure If malloc returns NULL due to low memory, 'config' pointer can be NULL. Add a check to prevent NULL dereference.

In the Linux kernel, the following vulnerability has been resolved: iommu/tegra241-cmdqv: Fix warnings due to dmam_free_coherent() Two WARNINGs are observed when SMMU driver rolls back upon failure: arm-smmu-v3.9.auto: Failed to register iommu arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22 ------------[ cut here ]------------ WARNING: CPU: 5 PID: 1 at kernel/dma/mapping.c:74 dmam_free_coherent+0xc0/0xd8 Call trace: dmam_free_coherent+0xc0/0xd8 (P) tegra241_vintf_free_lvcmdq+0x74/0x188 tegra241_cmdqv_remove_vintf+0x60/0x148 tegra241_cmdqv_remove+0x48/0xc8 arm_smmu_impl_remove+0x28/0x60 devm_action_release+0x1c/0x40 ------------[ cut here ]------------ 128 pages are still in use! WARNING: CPU: 16 PID: 1 at mm/page_alloc.c:6902 free_contig_range+0x18c/0x1c8 Call trace: free_contig_range+0x18c/0x1c8 (P) cma_release+0x154/0x2f0 dma_free_contiguous+0x38/0xa0 dma_direct_free+0x10c/0x248 dma_free_attrs+0x100/0x290 dmam_free_coherent+0x78/0xd8 tegra241_vintf_free_lvcmdq+0x74/0x160 tegra241_cmdqv_remove+0x98/0x198 arm_smmu_impl_remove+0x28/0x60 devm_action_release+0x1c/0x40 This is because the LVCMDQ queue memory are managed by devres, while that dmam_free_coherent() is called in the context of devm_action_release(). Jason pointed out that "arm_smmu_impl_probe() has mis-ordered the devres callbacks if ops->device_remove() is going to be manually freeing things that probe allocated": https://lore.kernel.org/linux-iommu/20250407174408.GB1722458@nvidia.com/ In fact, tegra241_cmdqv_init_structures() only allocates memory resources which means any failure that it generates would be similar to -ENOMEM, so there is no point in having that "falling back to standard SMMU" routine, as the standard SMMU would likely fail to allocate memory too. Remove the unwind part in tegra241_cmdqv_init_structures(), and return a proper error code to ask SMMU driver to call tegra241_cmdqv_remove() via impl_ops->device_remove(). Then, drop tegra241_vintf_free_lvcmdq() since devres will take care of that.

In the Linux kernel, the following vulnerability has been resolved: PCI: Fix reference leak in pci_register_host_bridge() If device_register() fails, call put_device() to give up the reference to avoid a memory leak, per the comment at device_register(). Found by code review. [bhelgaas: squash Dan Carpenter's double free fix from https://lore.kernel.org/r/db806a6c-a91b-4e5a-a84b-6b7e01bdac85@stanley.mountain]

PHPJabbers Cleaning Business Software v1.0 is vulnerable to Multiple Stored Cross-Site Scripting (XSS) in the "c_name, name" parameters.

PHPJabbers Event Booking Calendar v4.0 is vulnerable to Multiple HTML Injection in the "name, plugin_sms_api_key, plugin_sms_country_code, title, plugin_sms_api_key, title" parameters.

The TeleMessage archiving backend through 2025-05-05 accepts API calls (to request an authentication token) from the TM SGNL (aka Archive Signal) app with the credentials of logfile for the user and enRR8UVVywXYbFkqU#QDPRkO for the password.

In the Linux kernel, the following vulnerability has been resolved: mm/vmscan: don't try to reclaim hwpoison folio Syzkaller reports a bug as follows: Injecting memory failure for pfn 0x18b00e at process virtual address 0x20ffd000 Memory failure: 0x18b00e: dirty swapcache page still referenced by 2 users Memory failure: 0x18b00e: recovery action for dirty swapcache page: Failed page: refcount:2 mapcount:0 mapping:0000000000000000 index:0x20ffd pfn:0x18b00e memcg:ffff0000dd6d9000 anon flags: 0x5ffffe00482011(locked|dirty|arch_1|swapbacked|hwpoison|node=0|zone=2|lastcpupid=0xfffff) raw: 005ffffe00482011 dead000000000100 dead000000000122 ffff0000e232a7c9 raw: 0000000000020ffd 0000000000000000 00000002ffffffff ffff0000dd6d9000 page dumped because: VM_BUG_ON_FOLIO(!folio_test_uptodate(folio)) ------------[ cut here ]------------ kernel BUG at mm/swap_state.c:184! Internal error: Oops - BUG: 00000000f2000800 [#1] SMP Modules linked in: CPU: 0 PID: 60 Comm: kswapd0 Not tainted 6.6.0-gcb097e7de84e #3 Hardware name: linux,dummy-virt (DT) pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : add_to_swap+0xbc/0x158 lr : add_to_swap+0xbc/0x158 sp : ffff800087f37340 x29: ffff800087f37340 x28: fffffc00052c0380 x27: ffff800087f37780 x26: ffff800087f37490 x25: ffff800087f37c78 x24: ffff800087f377a0 x23: ffff800087f37c50 x22: 0000000000000000 x21: fffffc00052c03b4 x20: 0000000000000000 x19: fffffc00052c0380 x18: 0000000000000000 x17: 296f696c6f662865 x16: 7461646f7470755f x15: 747365745f6f696c x14: 6f6621284f494c4f x13: 0000000000000001 x12: ffff600036d8b97b x11: 1fffe00036d8b97a x10: ffff600036d8b97a x9 : dfff800000000000 x8 : 00009fffc9274686 x7 : ffff0001b6c5cbd3 x6 : 0000000000000001 x5 : ffff0000c25896c0 x4 : 0000000000000000 x3 : 0000000000000000 x2 : 0000000000000000 x1 : ffff0000c25896c0 x0 : 0000000000000000 Call trace: add_to_swap+0xbc/0x158 shrink_folio_list+0x12ac/0x2648 shrink_inactive_list+0x318/0x948 shrink_lruvec+0x450/0x720 shrink_node_memcgs+0x280/0x4a8 shrink_node+0x128/0x978 balance_pgdat+0x4f0/0xb20 kswapd+0x228/0x438 kthread+0x214/0x230 ret_from_fork+0x10/0x20 I can reproduce this issue with the following steps: 1) When a dirty swapcache page is isolated by reclaim process and the page isn't locked, inject memory failure for the page. me_swapcache_dirty() clears uptodate flag and tries to delete from lru, but fails. Reclaim process will put the hwpoisoned page back to lru. 2) The process that maps the hwpoisoned page exits, the page is deleted the page will never be freed and will be in the lru forever. 3) If we trigger a reclaim again and tries to reclaim the page, add_to_swap() will trigger VM_BUG_ON_FOLIO due to the uptodate flag is cleared. To fix it, skip the hwpoisoned page in shrink_folio_list(). Besides, the hwpoison folio may not be unmapped by hwpoison_user_mappings() yet, unmap it in shrink_folio_list(), otherwise the folio will fail to be unmaped by hwpoison_user_mappings() since the folio isn't in lru list.

In the Linux kernel, the following vulnerability has been resolved: net/niu: Niu requires MSIX ENTRY_DATA fields touch before entry reads Fix niu_try_msix() to not cause a fatal trap on sparc systems. Set PCI_DEV_FLAGS_MSIX_TOUCH_ENTRY_DATA_FIRST on the struct pci_dev to work around a bug in the hardware or firmware. For each vector entry in the msix table, niu chips will cause a fatal trap if any registers in that entry are read before that entries' ENTRY_DATA register is written to. Testing indicates writes to other registers are not sufficient to prevent the fatal trap, however the value does not appear to matter. This only needs to happen once after power up, so simply rebooting into a kernel lacking this fix will NOT cause the trap. NON-RESUMABLE ERROR: Reporting on cpu 64 NON-RESUMABLE ERROR: TPC [0x00000000005f6900] <msix_prepare_msi_desc+0x90/0xa0> NON-RESUMABLE ERROR: RAW [4010000000000016:00000e37f93e32ff:0000000202000080:ffffffffffffffff NON-RESUMABLE ERROR: 0000000800000000:0000000000000000:0000000000000000:0000000000000000] NON-RESUMABLE ERROR: handle [0x4010000000000016] stick [0x00000e37f93e32ff] NON-RESUMABLE ERROR: type [precise nonresumable] NON-RESUMABLE ERROR: attrs [0x02000080] < ASI sp-faulted priv > NON-RESUMABLE ERROR: raddr [0xffffffffffffffff] NON-RESUMABLE ERROR: insn effective address [0x000000c50020000c] NON-RESUMABLE ERROR: size [0x8] NON-RESUMABLE ERROR: asi [0x00] CPU: 64 UID: 0 PID: 745 Comm: kworker/64:1 Not tainted 6.11.5 #63 Workqueue: events work_for_cpu_fn TSTATE: 0000000011001602 TPC: 00000000005f6900 TNPC: 00000000005f6904 Y: 00000000 Not tainted TPC: <msix_prepare_msi_desc+0x90/0xa0> g0: 00000000000002e9 g1: 000000000000000c g2: 000000c50020000c g3: 0000000000000100 g4: ffff8000470307c0 g5: ffff800fec5be000 g6: ffff800047a08000 g7: 0000000000000000 o0: ffff800014feb000 o1: ffff800047a0b620 o2: 0000000000000011 o3: ffff800047a0b620 o4: 0000000000000080 o5: 0000000000000011 sp: ffff800047a0ad51 ret_pc: 00000000005f7128 RPC: <__pci_enable_msix_range+0x3cc/0x460> l0: 000000000000000d l1: 000000000000c01f l2: ffff800014feb0a8 l3: 0000000000000020 l4: 000000000000c000 l5: 0000000000000001 l6: 0000000020000000 l7: ffff800047a0b734 i0: ffff800014feb000 i1: ffff800047a0b730 i2: 0000000000000001 i3: 000000000000000d i4: 0000000000000000 i5: 0000000000000000 i6: ffff800047a0ae81 i7: 00000000101888b0 I7: <niu_try_msix.constprop.0+0xc0/0x130 [niu]> Call Trace: [<00000000101888b0>] niu_try_msix.constprop.0+0xc0/0x130 [niu] [<000000001018f840>] niu_get_invariants+0x183c/0x207c [niu] [<00000000101902fc>] niu_pci_init_one+0x27c/0x2fc [niu] [<00000000005ef3e4>] local_pci_probe+0x28/0x74 [<0000000000469240>] work_for_cpu_fn+0x8/0x1c [<000000000046b008>] process_scheduled_works+0x144/0x210 [<000000000046b518>] worker_thread+0x13c/0x1c0 [<00000000004710e0>] kthread+0xb8/0xc8 [<00000000004060c8>] ret_from_fork+0x1c/0x2c [<0000000000000000>] 0x0 Kernel panic - not syncing: Non-resumable error.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: apple-soc: Fix null-ptr-deref in apple_soc_cpufreq_get_rate() cpufreq_cpu_get_raw() can return NULL when the target CPU is not present in the policy->cpus mask. apple_soc_cpufreq_get_rate() does not check for this case, which results in a NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: scmi: Fix null-ptr-deref in scmi_cpufreq_get_rate() cpufreq_cpu_get_raw() can return NULL when the target CPU is not present in the policy->cpus mask. scmi_cpufreq_get_rate() does not check for this case, which results in a NULL pointer dereference. Add NULL check after cpufreq_cpu_get_raw() to prevent this issue.

In the Linux kernel, the following vulnerability has been resolved: cpufreq: scpi: Fix null-ptr-deref in scpi_cpufreq_get_rate() cpufreq_cpu_get_raw() can return NULL when the target CPU is not present in the policy->cpus mask. scpi_cpufreq_get_rate() does not check for this case, which results in a NULL pointer dereference.

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: mcq: Add NULL check in ufshcd_mcq_abort() A race can occur between the MCQ completion path and the abort handler: once a request completes, __blk_mq_free_request() sets rq->mq_hctx to NULL, meaning the subsequent ufshcd_mcq_req_to_hwq() call in ufshcd_mcq_abort() can return a NULL pointer. If this NULL pointer is dereferenced, the kernel will crash. Add a NULL check for the returned hwq pointer. If hwq is NULL, log an error and return FAILED, preventing a potential NULL-pointer dereference. As suggested by Bart, the ufshcd_cmd_inflight() check is removed. This is similar to the fix in commit 74736103fb41 ("scsi: ufs: core: Fix ufshcd_abort_one racing issue"). This is found by our static analysis tool KNighter.

In the Linux kernel, the following vulnerability has been resolved: btrfs: zoned: return EIO on RAID1 block group write pointer mismatch There was a bug report about a NULL pointer dereference in __btrfs_add_free_space_zoned() that ultimately happens because a conversion from the default metadata profile DUP to a RAID1 profile on two disks. The stack trace has the following signature: BTRFS error (device sdc): zoned: write pointer offset mismatch of zones in raid1 profile BUG: kernel NULL pointer dereference, address: 0000000000000058 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI RIP: 0010:__btrfs_add_free_space_zoned.isra.0+0x61/0x1a0 RSP: 0018:ffffa236b6f3f6d0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: ffff96c8132f3400 RCX: 0000000000000001 RDX: 0000000010000000 RSI: 0000000000000000 RDI: ffff96c8132f3410 RBP: 0000000010000000 R08: 0000000000000003 R09: 0000000000000000 R10: 0000000000000000 R11: 00000000ffffffff R12: 0000000000000000 R13: ffff96c758f65a40 R14: 0000000000000001 R15: 000011aac0000000 FS: 00007fdab1cb2900(0000) GS:ffff96e60ca00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000058 CR3: 00000001a05ae000 CR4: 0000000000350ef0 Call Trace: <TASK> ? __die_body.cold+0x19/0x27 ? page_fault_oops+0x15c/0x2f0 ? exc_page_fault+0x7e/0x180 ? asm_exc_page_fault+0x26/0x30 ? __btrfs_add_free_space_zoned.isra.0+0x61/0x1a0 btrfs_add_free_space_async_trimmed+0x34/0x40 btrfs_add_new_free_space+0x107/0x120 btrfs_make_block_group+0x104/0x2b0 btrfs_create_chunk+0x977/0xf20 btrfs_chunk_alloc+0x174/0x510 ? srso_return_thunk+0x5/0x5f btrfs_inc_block_group_ro+0x1b1/0x230 btrfs_relocate_block_group+0x9e/0x410 btrfs_relocate_chunk+0x3f/0x130 btrfs_balance+0x8ac/0x12b0 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? __kmalloc_cache_noprof+0x14c/0x3e0 btrfs_ioctl+0x2686/0x2a80 ? srso_return_thunk+0x5/0x5f ? ioctl_has_perm.constprop.0.isra.0+0xd2/0x120 __x64_sys_ioctl+0x97/0xc0 do_syscall_64+0x82/0x160 ? srso_return_thunk+0x5/0x5f ? __memcg_slab_free_hook+0x11a/0x170 ? srso_return_thunk+0x5/0x5f ? kmem_cache_free+0x3f0/0x450 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? syscall_exit_to_user_mode+0x10/0x210 ? srso_return_thunk+0x5/0x5f ? do_syscall_64+0x8e/0x160 ? sysfs_emit+0xaf/0xc0 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? seq_read_iter+0x207/0x460 ? srso_return_thunk+0x5/0x5f ? vfs_read+0x29c/0x370 ? srso_return_thunk+0x5/0x5f ? srso_return_thunk+0x5/0x5f ? syscall_exit_to_user_mode+0x10/0x210 ? srso_return_thunk+0x5/0x5f ? do_syscall_64+0x8e/0x160 ? srso_return_thunk+0x5/0x5f ? exc_page_fault+0x7e/0x180 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fdab1e0ca6d RSP: 002b:00007ffeb2b60c80 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007fdab1e0ca6d RDX: 00007ffeb2b60d80 RSI: 00000000c4009420 RDI: 0000000000000003 RBP: 00007ffeb2b60cd0 R08: 0000000000000000 R09: 0000000000000013 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00007ffeb2b6343b R14: 00007ffeb2b60d80 R15: 0000000000000001 </TASK> CR2: 0000000000000058 ---[ end trace 0000000000000000 ]--- The 1st line is the most interesting here: BTRFS error (device sdc): zoned: write pointer offset mismatch of zones in raid1 profile When a RAID1 block-group is created and a write pointer mismatch between the disks in the RAID set is detected, btrfs sets the alloc_offset to the length of the block group marking it as full. Afterwards the code expects that a balance operation will evacuate the data in this block-group and repair the problems. But before this is possible, the new space of this block-group will be accounted in the free space cache. But in __btrfs_ ---truncated---

In the Linux kernel, the following vulnerability has been resolved: scsi: ufs: core: Add NULL check in ufshcd_mcq_compl_pending_transfer() Add a NULL check for the returned hwq pointer by ufshcd_mcq_req_to_hwq(). This is similar to the fix in commit 74736103fb41 ("scsi: ufs: core: Fix ufshcd_abort_one racing issue").

In the Linux kernel, the following vulnerability has been resolved: tipc: fix NULL pointer dereference in tipc_mon_reinit_self() syzbot reported: tipc: Node number set to 1055423674 Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] CPU: 3 UID: 0 PID: 6017 Comm: kworker/3:5 Not tainted 6.15.0-rc1-syzkaller-00246-g900241a5cc15 #0 PREEMPT(full) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014 Workqueue: events tipc_net_finalize_work RIP: 0010:tipc_mon_reinit_self+0x11c/0x210 net/tipc/monitor.c:719 ... RSP: 0018:ffffc9000356fb68 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003ee87cba RDX: 0000000000000000 RSI: ffffffff8dbc56a7 RDI: ffff88804c2cc010 RBP: dffffc0000000000 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007 R13: fffffbfff2111097 R14: ffff88804ead8000 R15: ffff88804ead9010 FS: 0000000000000000(0000) GS:ffff888097ab9000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000f720eb00 CR3: 000000000e182000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> tipc_net_finalize+0x10b/0x180 net/tipc/net.c:140 process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238 process_scheduled_works kernel/workqueue.c:3319 [inline] worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400 kthread+0x3c2/0x780 kernel/kthread.c:464 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245 </TASK> ... RIP: 0010:tipc_mon_reinit_self+0x11c/0x210 net/tipc/monitor.c:719 ... RSP: 0018:ffffc9000356fb68 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003ee87cba RDX: 0000000000000000 RSI: ffffffff8dbc56a7 RDI: ffff88804c2cc010 RBP: dffffc0000000000 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007 R13: fffffbfff2111097 R14: ffff88804ead8000 R15: ffff88804ead9010 FS: 0000000000000000(0000) GS:ffff888097ab9000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000f720eb00 CR3: 000000000e182000 CR4: 0000000000352ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 There is a racing condition between workqueue created when enabling bearer and another thread created when disabling bearer right after that as follow: enabling_bearer | disabling_bearer --------------- | ---------------- tipc_disc_timeout() | { | bearer_disable() ... | { schedule_work(&tn->work); | tipc_mon_delete() ... | { } | ... | write_lock_bh(&mon->lock); | mon->self = NULL; | write_unlock_bh(&mon->lock); | ... | } tipc_net_finalize_work() | } { | ... | tipc_net_finalize() | { | ... | tipc_mon_reinit_self() | { | ... | write_lock_bh(&mon->lock); | mon->self->addr = tipc_own_addr(net); | write_unlock_bh(&mon->lock); | ... ---truncated---

In the Linux kernel, the following vulnerability has been resolved: sched/eevdf: Fix se->slice being set to U64_MAX and resulting crash There is a code path in dequeue_entities() that can set the slice of a sched_entity to U64_MAX, which sometimes results in a crash. The offending case is when dequeue_entities() is called to dequeue a delayed group entity, and then the entity's parent's dequeue is delayed. In that case: 1. In the if (entity_is_task(se)) else block at the beginning of dequeue_entities(), slice is set to cfs_rq_min_slice(group_cfs_rq(se)). If the entity was delayed, then it has no queued tasks, so cfs_rq_min_slice() returns U64_MAX. 2. The first for_each_sched_entity() loop dequeues the entity. 3. If the entity was its parent's only child, then the next iteration tries to dequeue the parent. 4. If the parent's dequeue needs to be delayed, then it breaks from the first for_each_sched_entity() loop _without updating slice_. 5. The second for_each_sched_entity() loop sets the parent's ->slice to the saved slice, which is still U64_MAX. This throws off subsequent calculations with potentially catastrophic results. A manifestation we saw in production was: 6. In update_entity_lag(), se->slice is used to calculate limit, which ends up as a huge negative number. 7. limit is used in se->vlag = clamp(vlag, -limit, limit). Because limit is negative, vlag > limit, so se->vlag is set to the same huge negative number. 8. In place_entity(), se->vlag is scaled, which overflows and results in another huge (positive or negative) number. 9. The adjusted lag is subtracted from se->vruntime, which increases or decreases se->vruntime by a huge number. 10. pick_eevdf() calls entity_eligible()/vruntime_eligible(), which incorrectly returns false because the vruntime is so far from the other vruntimes on the queue, causing the (vruntime - cfs_rq->min_vruntime) * load calulation to overflow. 11. Nothing appears to be eligible, so pick_eevdf() returns NULL. 12. pick_next_entity() tries to dereference the return value of pick_eevdf() and crashes. Dumping the cfs_rq states from the core dumps with drgn showed tell-tale huge vruntime ranges and bogus vlag values, and I also traced se->slice being set to U64_MAX on live systems (which was usually "benign" since the rest of the runqueue needed to be in a particular state to crash). Fix it in dequeue_entities() by always setting slice from the first non-empty cfs_rq.

In the Linux kernel, the following vulnerability has been resolved: xen-netfront: handle NULL returned by xdp_convert_buff_to_frame() The function xdp_convert_buff_to_frame() may return NULL if it fails to correctly convert the XDP buffer into an XDP frame due to memory constraints, internal errors, or invalid data. Failing to check for NULL may lead to a NULL pointer dereference if the result is used later in processing, potentially causing crashes, data corruption, or undefined behavior. On XDP redirect failure, the associated page must be released explicitly if it was previously retained via get_page(). Failing to do so may result in a memory leak, as the pages reference count is not decremented.

In the Linux kernel, the following vulnerability has been resolved: LoongArch: Return NULL from huge_pte_offset() for invalid PMD LoongArch's huge_pte_offset() currently returns a pointer to a PMD slot even if the underlying entry points to invalid_pte_table (indicating no mapping). Callers like smaps_hugetlb_range() fetch this invalid entry value (the address of invalid_pte_table) via this pointer. The generic is_swap_pte() check then incorrectly identifies this address as a swap entry on LoongArch, because it satisfies the "!pte_present() && !pte_none()" conditions. This misinterpretation, combined with a coincidental match by is_migration_entry() on the address bits, leads to kernel crashes in pfn_swap_entry_to_page(). Fix this at the architecture level by modifying huge_pte_offset() to check the PMD entry's content using pmd_none() before returning. If the entry is invalid (i.e., it points to invalid_pte_table), return NULL instead of the pointer to the slot.

In the Linux kernel, the following vulnerability has been resolved: mei: vsc: Fix fortify-panic caused by invalid counted_by() use gcc 15 honors the __counted_by(len) attribute on vsc_tp_packet.buf[] and the vsc-tp.c code is using this in a wrong way. len does not contain the available size in the buffer, it contains the actual packet length *without* the crc. So as soon as vsc_tp_xfer() tries to add the crc to buf[] the fortify-panic handler gets triggered: [ 80.842193] memcpy: detected buffer overflow: 4 byte write of buffer size 0 [ 80.842243] WARNING: CPU: 4 PID: 272 at lib/string_helpers.c:1032 __fortify_report+0x45/0x50 ... [ 80.843175] __fortify_panic+0x9/0xb [ 80.843186] vsc_tp_xfer.cold+0x67/0x67 [mei_vsc_hw] [ 80.843210] ? seqcount_lockdep_reader_access.constprop.0+0x82/0x90 [ 80.843229] ? lockdep_hardirqs_on+0x7c/0x110 [ 80.843250] mei_vsc_hw_start+0x98/0x120 [mei_vsc] [ 80.843270] mei_reset+0x11d/0x420 [mei] The easiest fix would be to just drop the counted-by but with the exception of the ack buffer in vsc_tp_xfer_helper() which only contains enough room for the packet-header, all other uses of vsc_tp_packet always use a buffer of VSC_TP_MAX_XFER_SIZE bytes for the packet. Instead of just dropping the counted-by, split the vsc_tp_packet struct definition into a header and a full-packet definition and use a fixed size buf[] in the packet definition, this way fortify-source buffer overrun checking still works when enabled.

In the Linux kernel, the following vulnerability has been resolved: misc: microchip: pci1xxxx: Fix Kernel panic during IRQ handler registration Resolve kernel panic while accessing IRQ handler associated with the generated IRQ. This is done by acquiring the spinlock and storing the current interrupt state before handling the interrupt request using generic_handle_irq. A previous fix patch was submitted where 'generic_handle_irq' was replaced with 'handle_nested_irq'. However, this change also causes the kernel panic where after determining which GPIO triggered the interrupt and attempting to call handle_nested_irq with the mapped IRQ number, leads to a failure in locating the registered handler.

In the Linux kernel, the following vulnerability has been resolved: tty: Require CAP_SYS_ADMIN for all usages of TIOCL_SELMOUSEREPORT This requirement was overeagerly loosened in commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), but as it turns out, (1) the logic I implemented there was inconsistent (apologies!), (2) TIOCL_SELMOUSEREPORT might actually be a small security risk after all, and (3) TIOCL_SELMOUSEREPORT is only meant to be used by the mouse daemon (GPM or Consolation), which runs as CAP_SYS_ADMIN already. In more detail: 1. The previous patch has inconsistent logic: In commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"), we checked for sel_mode == TIOCL_SELMOUSEREPORT, but overlooked that the lower four bits of this "mode" parameter were actually used as an additional way to pass an argument. So the patch did actually still require CAP_SYS_ADMIN, if any of the mouse button bits are set, but did not require it if none of the mouse buttons bits are set. This logic is inconsistent and was not intentional. We should have the same policies for using TIOCL_SELMOUSEREPORT independent of the value of the "hidden" mouse button argument. I sent a separate documentation patch to the man page list with more details on TIOCL_SELMOUSEREPORT: https://lore.kernel.org/all/20250223091342.35523-2-gnoack3000@gmail.com/ 2. TIOCL_SELMOUSEREPORT is indeed a potential security risk which can let an attacker simulate "keyboard" input to command line applications on the same terminal, like TIOCSTI and some other TIOCLINUX "selection mode" IOCTLs. By enabling mouse reporting on a terminal and then injecting mouse reports through TIOCL_SELMOUSEREPORT, an attacker can simulate mouse movements on the same terminal, similar to the TIOCSTI keystroke injection attacks that were previously possible with TIOCSTI and other TIOCL_SETSEL selection modes. Many programs (including libreadline/bash) are then prone to misinterpret these mouse reports as normal keyboard input because they do not expect input in the X11 mouse protocol form. The attacker does not have complete control over the escape sequence, but they can at least control the values of two consecutive bytes in the binary mouse reporting escape sequence. I went into more detail on that in the discussion at https://lore.kernel.org/all/20250221.0a947528d8f3@gnoack.org/ It is not equally trivial to simulate arbitrary keystrokes as it was with TIOCSTI (commit 83efeeeb3d04 ("tty: Allow TIOCSTI to be disabled")), but the general mechanism is there, and together with the small number of existing legit use cases (see below), it would be better to revert back to requiring CAP_SYS_ADMIN for TIOCL_SELMOUSEREPORT, as it was already the case before commit 2f83e38a095f ("tty: Permit some TIOCL_SETSEL modes without CAP_SYS_ADMIN"). 3. TIOCL_SELMOUSEREPORT is only used by the mouse daemons (GPM or Consolation), and they are the only legit use case: To quote console_codes(4): The mouse tracking facility is intended to return xterm(1)-compatible mouse status reports. Because the console driver has no way to know the device or type of the mouse, these reports are returned in the console input stream only when the virtual terminal driver receives a mouse update ioctl. These ioctls must be generated by a mouse-aware user-mode application such as the gpm(8) daemon. Jared Finder has also confirmed in https://lore.kernel.org/all/491f3df9de6593df8e70dbe77614b026@finder.org/ that Emacs does not call TIOCL_SELMOUSEREPORT directly, and it would be difficult to find good reasons for doing that, given that it would interfere with the reports that GPM is sending. More information on the interaction between GPM, terminals and th ---truncated---

In the Linux kernel, the following vulnerability has been resolved: usb: xhci: Fix invalid pointer dereference in Etron workaround This check is performed before prepare_transfer() and prepare_ring(), so enqueue can already point at the final link TRB of a segment. And indeed it will, some 0.4% of times this code is called. Then enqueue + 1 is an invalid pointer. It will crash the kernel right away or load some junk which may look like a link TRB and cause the real link TRB to be replaced with a NOOP. This wouldn't end well. Use a functionally equivalent test which doesn't dereference the pointer and always gives correct result. Something has crashed my machine twice in recent days while playing with an Etron HC, and a control transfer stress test ran for confirmation has just crashed it again. The same test passes with this patch applied.

In the Linux kernel, the following vulnerability has been resolved: usb: cdns3: Fix deadlock when using NCM gadget The cdns3 driver has the same NCM deadlock as fixed in cdnsp by commit 58f2fcb3a845 ("usb: cdnsp: Fix deadlock issue during using NCM gadget"). Under PREEMPT_RT the deadlock can be readily triggered by heavy network traffic, for example using "iperf --bidir" over NCM ethernet link. The deadlock occurs because the threaded interrupt handler gets preempted by a softirq, but both are protected by the same spinlock. Prevent deadlock by disabling softirq during threaded irq handler.

In the Linux kernel, the following vulnerability has been resolved: usb: chipidea: ci_hdrc_imx: fix usbmisc handling usbmisc is an optional device property so it is totally valid for the corresponding data->usbmisc_data to have a NULL value. Check that before dereferencing the pointer. Found by Linux Verification Center (linuxtesting.org) with Svace static analysis tool.

In the Linux kernel, the following vulnerability has been resolved: usb: typec: class: Fix NULL pointer access Concurrent calls to typec_partner_unlink_device can lead to a NULL pointer dereference. This patch adds a mutex to protect USB device pointers and prevent this issue. The same mutex protects both the device pointers and the partner device registration.

In the Linux kernel, the following vulnerability has been resolved: crypto: null - Use spin lock instead of mutex As the null algorithm may be freed in softirq context through af_alg, use spin locks instead of mutexes to protect the default null algorithm.

In the Linux kernel, the following vulnerability has been resolved: bpf: Fix kmemleak warning for percpu hashmap Vlad Poenaru reported the following kmemleak issue: unreferenced object 0x606fd7c44ac8 (size 32): backtrace (crc 0): pcpu_alloc_noprof+0x730/0xeb0 bpf_map_alloc_percpu+0x69/0xc0 prealloc_init+0x9d/0x1b0 htab_map_alloc+0x363/0x510 map_create+0x215/0x3a0 __sys_bpf+0x16b/0x3e0 __x64_sys_bpf+0x18/0x20 do_syscall_64+0x7b/0x150 entry_SYSCALL_64_after_hwframe+0x4b/0x53 Further investigation shows the reason is due to not 8-byte aligned store of percpu pointer in htab_elem_set_ptr(): *(void __percpu **)(l->key + key_size) = pptr; Note that the whole htab_elem alignment is 8 (for x86_64). If the key_size is 4, that means pptr is stored in a location which is 4 byte aligned but not 8 byte aligned. In mm/kmemleak.c, scan_block() scans the memory based on 8 byte stride, so it won't detect above pptr, hence reporting the memory leak. In htab_map_alloc(), we already have htab->elem_size = sizeof(struct htab_elem) + round_up(htab->map.key_size, 8); if (percpu) htab->elem_size += sizeof(void *); else htab->elem_size += round_up(htab->map.value_size, 8); So storing pptr with 8-byte alignment won't cause any problem and can fix kmemleak too. The issue can be reproduced with bpf selftest as well: 1. Enable CONFIG_DEBUG_KMEMLEAK config 2. Add a getchar() before skel destroy in test_hash_map() in prog_tests/for_each.c. The purpose is to keep map available so kmemleak can be detected. 3. run './test_progs -t for_each/hash_map &' and a kmemleak should be reported.

In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Keep write operations atomic syzbot reported a NULL pointer dereference in __generic_file_write_iter. [1] Before the write operation is completed, the user executes ioctl[2] to clear the compress flag of the file, which causes the is_compressed() judgment to return 0, further causing the program to enter the wrong process and call the wrong ops ntfs_aops_cmpr, which triggers the null pointer dereference of write_begin. Use inode lock to synchronize ioctl and write to avoid this case. [1] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Mem abort info: ESR = 0x0000000086000006 EC = 0x21: IABT (current EL), IL = 32 bits SET = 0, FnV = 0 EA = 0, S1PTW = 0 FSC = 0x06: level 2 translation fault user pgtable: 4k pages, 48-bit VAs, pgdp=000000011896d000 [0000000000000000] pgd=0800000118b44403, p4d=0800000118b44403, pud=0800000117517403, pmd=0000000000000000 Internal error: Oops: 0000000086000006 [#1] PREEMPT SMP Modules linked in: CPU: 0 UID: 0 PID: 6427 Comm: syz-executor347 Not tainted 6.13.0-rc3-syzkaller-g573067a5a685 #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/13/2024 pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : 0x0 lr : generic_perform_write+0x29c/0x868 mm/filemap.c:4055 sp : ffff80009d4978a0 x29: ffff80009d4979c0 x28: dfff800000000000 x27: ffff80009d497bc8 x26: 0000000000000000 x25: ffff80009d497960 x24: ffff80008ba71c68 x23: 0000000000000000 x22: ffff0000c655dac0 x21: 0000000000001000 x20: 000000000000000c x19: 1ffff00013a92f2c x18: ffff0000e183aa1c x17: 0004060000000014 x16: ffff800083275834 x15: 0000000000000001 x14: 0000000000000000 x13: 0000000000000001 x12: ffff0000c655dac0 x11: 0000000000ff0100 x10: 0000000000ff0100 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : ffff80009d497980 x4 : ffff80009d497960 x3 : 0000000000001000 x2 : 0000000000000000 x1 : ffff0000e183a928 x0 : ffff0000d60b0fc0 Call trace: 0x0 (P) __generic_file_write_iter+0xfc/0x204 mm/filemap.c:4156 ntfs_file_write_iter+0x54c/0x630 fs/ntfs3/file.c:1267 new_sync_write fs/read_write.c:586 [inline] vfs_write+0x920/0xcf4 fs/read_write.c:679 ksys_write+0x15c/0x26c fs/read_write.c:731 __do_sys_write fs/read_write.c:742 [inline] __se_sys_write fs/read_write.c:739 [inline] __arm64_sys_write+0x7c/0x90 fs/read_write.c:739 __invoke_syscall arch/arm64/kernel/syscall.c:35 [inline] invoke_syscall+0x98/0x2b8 arch/arm64/kernel/syscall.c:49 el0_svc_common+0x130/0x23c arch/arm64/kernel/syscall.c:132 do_el0_svc+0x48/0x58 arch/arm64/kernel/syscall.c:151 el0_svc+0x54/0x168 arch/arm64/kernel/entry-common.c:744 el0t_64_sync_handler+0x84/0x108 arch/arm64/kernel/entry-common.c:762 [2] ioctl$FS_IOC_SETFLAGS(r0, 0x40086602, &(0x7f00000000c0)=0x20)

In the Linux kernel, the following vulnerability has been resolved: sound/virtio: Fix cancel_sync warnings on uninitialized work_structs Betty reported hitting the following warning: [ 8.709131][ T221] WARNING: CPU: 2 PID: 221 at kernel/workqueue.c:4182 ... [ 8.713282][ T221] Call trace: [ 8.713365][ T221] __flush_work+0x8d0/0x914 [ 8.713468][ T221] __cancel_work_sync+0xac/0xfc [ 8.713570][ T221] cancel_work_sync+0x24/0x34 [ 8.713667][ T221] virtsnd_remove+0xa8/0xf8 [virtio_snd ab15f34d0dd772f6d11327e08a81d46dc9c36276] [ 8.713868][ T221] virtsnd_probe+0x48c/0x664 [virtio_snd ab15f34d0dd772f6d11327e08a81d46dc9c36276] [ 8.714035][ T221] virtio_dev_probe+0x28c/0x390 [ 8.714139][ T221] really_probe+0x1bc/0x4c8 ... It seems we're hitting the error path in virtsnd_probe(), which triggers a virtsnd_remove() which iterates over the substreams calling cancel_work_sync() on the elapsed_period work_struct. Looking at the code, from earlier in: virtsnd_probe()->virtsnd_build_devs()->virtsnd_pcm_parse_cfg() We set snd->nsubstreams, allocate the snd->substreams, and if we then hit an error on the info allocation or something in virtsnd_ctl_query_info() fails, we will exit without having initialized the elapsed_period work_struct. When that error path unwinds we then call virtsnd_remove() which as long as the substreams array is allocated, will iterate through calling cancel_work_sync() on the uninitialized work struct hitting this warning. Takashi Iwai suggested this fix, which initializes the substreams structure right after allocation, so that if we hit the error paths we avoid trying to cleanup uninitialized data. Note: I have not yet managed to reproduce the issue myself, so this patch has had limited testing. Feedback or thoughts would be appreciated!

In the Linux kernel, the following vulnerability has been resolved: spi: spi-imx: Add check for spi_imx_setupxfer() Add check for the return value of spi_imx_setupxfer(). spi_imx->rx and spi_imx->tx function pointer can be NULL when spi_imx_setupxfer() return error, and make NULL pointer dereference. Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000 Call trace: 0x0 spi_imx_pio_transfer+0x50/0xd8 spi_imx_transfer_one+0x18c/0x858 spi_transfer_one_message+0x43c/0x790 __spi_pump_transfer_message+0x238/0x5d4 __spi_sync+0x2b0/0x454 spi_write_then_read+0x11c/0x200

Craft CMS stores arbitrary content provided by unauthenticated users in session files. This content could be accessed and executed, possibly using an independent vulnerability. Craft CMS redirects requests that require authentication to the login page and generates a session file on the server at '/var/lib/php/sessions'. Such session files are named 'sess_[session_value]', where '[session_value]' is provided to the client in a 'Set-Cookie' response header. Craft CMS stores the return URL requested by the client without sanitizing parameters. Consequently, an unauthenticated client can introduce arbitrary values, such as PHP code, to a known local file location on the server. Craft CMS versions 5.7.5 and 4.15.3 have been released to address this issue.