In the Linux kernel, the following vulnerability has been resolved:
fbnic: close fw_log race between users and teardown
Fixes a theoretical race on fw_log between the teardown path and fw_log
write functions.
fw_log is written inside fbnic_fw_log_write() and can be reached from
the mailbox handler fbnic_fw_msix_intr(), but fw_log is freed before
IRQ/MBX teardown during cleanup, resulting in a potential data race of
dereferencing a freed/null variable.
Possible Interleaving Scenario:
CPU0: fbnic_fw_msix_intr() // Entry
fbnic_fw_log_write()
if (fbnic_fw_log_ready()) // true
... preempt ...
CPU1: fbnic_remove() // Entry
fbnic_fw_log_free()
vfree(log->data_start);
log->data_start = NULL;
CPU0: continues, walks log->entries or writes to log->data_start
The initialization also has an incorrect order problem, as the fw_log
is currently allocated after MBX setup during initialization.
Fix the problems by adjusting the synchronization order to put
initialization in place before the mailbox is enabled, and not cleared
until after the mailbox has been disabled.
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix memory leak in amdgpu_ras_init()
When amdgpu_nbio_ras_sw_init() fails in amdgpu_ras_init(), the function
returns directly without freeing the allocated con structure, leading
to a memory leak.
Fix this by jumping to the release_con label to properly clean up the
allocated memory before returning the error code.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
In the Linux kernel, the following vulnerability has been resolved:
ublk: use READ_ONCE() to read struct ublksrv_ctrl_cmd
struct ublksrv_ctrl_cmd is part of the io_uring_sqe, which may lie in
userspace-mapped memory. It's racy to access its fields with normal
loads, as userspace may write to them concurrently. Use READ_ONCE() to
copy the ublksrv_ctrl_cmd from the io_uring_sqe to the stack. Use the
local copy in place of the one in the io_uring_sqe.
In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix invalid leaf access in btrfs_quota_enable() if ref key not found
If btrfs_search_slot_for_read() returns 1, it means we did not find any
key greater than or equals to the key we asked for, meaning we have
reached the end of the tree and therefore the path is not valid. If
this happens we need to break out of the loop and stop, instead of
continuing and accessing an invalid path.
In the Linux kernel, the following vulnerability has been resolved:
RDMA/mlx5: Fix UMR hang in LAG error state unload
During firmware reset in LAG mode, a race condition causes the driver
to hang indefinitely while waiting for UMR completion during device
unload. See [1].
In LAG mode the bond device is only registered on the master, so it
never sees sys_error events from the slave.
During firmware reset this causes UMR waits to hang forever on unload
as the slave is dead but the master hasn't entered error state yet, so
UMR posts succeed but completions never arrive.
Fix this by adding a sys_error notifier that gets registered before
MLX5_IB_STAGE_IB_REG and stays alive until after ib_unregister_device().
This ensures error events reach the bond device throughout teardown.
[1]
Call Trace:
__schedule+0x2bd/0x760
schedule+0x37/0xa0
schedule_preempt_disabled+0xa/0x10
__mutex_lock.isra.6+0x2b5/0x4a0
__mlx5_ib_dereg_mr+0x606/0x870 [mlx5_ib]
? __xa_erase+0x4a/0xa0
? _cond_resched+0x15/0x30
? wait_for_completion+0x31/0x100
ib_dereg_mr_user+0x48/0xc0 [ib_core]
? rdmacg_uncharge_hierarchy+0xa0/0x100
destroy_hw_idr_uobject+0x20/0x50 [ib_uverbs]
uverbs_destroy_uobject+0x37/0x150 [ib_uverbs]
__uverbs_cleanup_ufile+0xda/0x140 [ib_uverbs]
uverbs_destroy_ufile_hw+0x3a/0xf0 [ib_uverbs]
ib_uverbs_remove_one+0xc3/0x140 [ib_uverbs]
remove_client_context+0x8b/0xd0 [ib_core]
disable_device+0x8c/0x130 [ib_core]
__ib_unregister_device+0x10d/0x180 [ib_core]
ib_unregister_device+0x21/0x30 [ib_core]
__mlx5_ib_remove+0x1e4/0x1f0 [mlx5_ib]
auxiliary_bus_remove+0x1e/0x30
device_release_driver_internal+0x103/0x1f0
bus_remove_device+0xf7/0x170
device_del+0x181/0x410
mlx5_rescan_drivers_locked.part.10+0xa9/0x1d0 [mlx5_core]
mlx5_disable_lag+0x253/0x260 [mlx5_core]
mlx5_lag_disable_change+0x89/0xc0 [mlx5_core]
mlx5_eswitch_disable+0x67/0xa0 [mlx5_core]
mlx5_unload+0x15/0xd0 [mlx5_core]
mlx5_unload_one+0x71/0xc0 [mlx5_core]
mlx5_sync_reset_reload_work+0x83/0x100 [mlx5_core]
process_one_work+0x1a7/0x360
worker_thread+0x30/0x390
? create_worker+0x1a0/0x1a0
kthread+0x116/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x22/0x40
In the Linux kernel, the following vulnerability has been resolved:
bpf: Limit bpf program signature size
Practical BPF signatures are significantly smaller than
KMALLOC_MAX_CACHE_SIZE
Allowing larger sizes opens the door for abuse by passing excessive
size values and forcing the kernel into expensive allocation paths (via
kmalloc_large or vmalloc).
In the Linux kernel, the following vulnerability has been resolved:
HID: playstation: Add missing check for input_ff_create_memless
The ps_gamepad_create() function calls input_ff_create_memless()
without verifying its return value, which can lead to incorrect
behavior or potential crashes when FF effects are triggered.
Add a check for the return value of input_ff_create_memless().
In the Linux kernel, the following vulnerability has been resolved:
cpuidle: Skip governor when only one idle state is available
On certain platforms (PowerNV systems without a power-mgt DT node),
cpuidle may register only a single idle state. In cases where that
single state is a polling state (state 0), the ladder governor may
incorrectly treat state 1 as the first usable state and pass an
out-of-bounds index. This can lead to a NULL enter callback being
invoked, ultimately resulting in a system crash.
[ 13.342636] cpuidle-powernv : Only Snooze is available
[ 13.351854] Faulting instruction address: 0x00000000
[ 13.376489] NIP [0000000000000000] 0x0
[ 13.378351] LR [c000000001e01974] cpuidle_enter_state+0x2c4/0x668
Fix this by adding a bail-out in cpuidle_select() that returns state 0
directly when state_count <= 1, bypassing the governor and keeping the
tick running.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Return proper address for non-zero offsets in insn array
The map_direct_value_addr() function of the instruction
array map incorrectly adds offset to the resulting address.
This is a bug, because later the resolve_pseudo_ldimm64()
function adds the offset. Fix it. Corresponding selftests
are added in a consequent commit.
In the Linux kernel, the following vulnerability has been resolved:
apparmor: fix NULL pointer dereference in __unix_needs_revalidation
When receiving file descriptors via SCM_RIGHTS, both the socket pointer
and the socket's sk pointer can be NULL during socket setup or teardown,
causing NULL pointer dereferences in __unix_needs_revalidation().
This is a regression in AppArmor 5.0.0 (kernel 6.17+) where the new
__unix_needs_revalidation() function was added without proper NULL checks.
The crash manifests as:
BUG: kernel NULL pointer dereference, address: 0x0000000000000018
RIP: aa_file_perm+0xb7/0x3b0 (or +0xbe/0x3b0, +0xc0/0x3e0)
Call Trace:
apparmor_file_receive+0x42/0x80
security_file_receive+0x2e/0x50
receive_fd+0x1d/0xf0
scm_detach_fds+0xad/0x1c0
The function dereferences sock->sk->sk_family without checking if either
sock or sock->sk is NULL first.
Add NULL checks for both sock and sock->sk before accessing sk_family.
In the Linux kernel, the following vulnerability has been resolved:
SUNRPC: fix gss_auth kref leak in gss_alloc_msg error path
Commit 5940d1cf9f42 ("SUNRPC: Rebalance a kref in auth_gss.c") added
a kref_get(&gss_auth->kref) call to balance the gss_put_auth() done
in gss_release_msg(), but forgot to add a corresponding kref_put()
on the error path when kstrdup_const() fails.
If service_name is non-NULL and kstrdup_const() fails, the function
jumps to err_put_pipe_version which calls put_pipe_version() and
kfree(gss_msg), but never releases the gss_auth reference. This leads
to a kref leak where the gss_auth structure is never freed.
Add a forward declaration for gss_free_callback() and call kref_put()
in the err_put_pipe_version error path to properly release the
reference taken earlier.
In the Linux kernel, the following vulnerability has been resolved:
ASoC: nau8821: Cancel delayed work on component remove
Attempting to unload the driver while a jack detection work is pending
would likely crash the kernel when it is eventually scheduled for
execution:
[ 1984.896308] BUG: unable to handle page fault for address: ffffffffc10c2a20
[...]
[ 1984.896388] Hardware name: Valve Jupiter/Jupiter, BIOS F7A0131 01/30/2024
[ 1984.896396] Workqueue: events nau8821_jdet_work [snd_soc_nau8821]
[ 1984.896414] RIP: 0010:__mutex_lock+0x9f/0x11d0
[...]
[ 1984.896504] Call Trace:
[ 1984.896511] <TASK>
[ 1984.896524] ? snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core]
[ 1984.896572] ? snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core]
[ 1984.896596] snd_soc_dapm_disable_pin+0x26/0x60 [snd_soc_core]
[ 1984.896622] nau8821_jdet_work+0xeb/0x1e0 [snd_soc_nau8821]
[ 1984.896636] process_one_work+0x211/0x590
[ 1984.896649] ? srso_return_thunk+0x5/0x5f
[ 1984.896670] worker_thread+0x1cd/0x3a0
Cancel unscheduled jdet_work or wait for its execution to finish before
the component driver gets removed.
In the Linux kernel, the following vulnerability has been resolved:
ublk: Validate SQE128 flag before accessing the cmd
ublk_ctrl_cmd_dump() accesses (header *)sqe->cmd before
IO_URING_F_SQE128 flag check. This could cause out of boundary memory
access.
Move the SQE128 flag check earlier in ublk_ctrl_uring_cmd() to return
-EINVAL immediately if the flag is not set.
In the Linux kernel, the following vulnerability has been resolved:
gfs2: fix memory leaks in gfs2_fill_super error path
Fix two memory leaks in the gfs2_fill_super() error handling path when
transitioning a filesystem to read-write mode fails.
First leak: kthread objects (thread_struct, task_struct, etc.)
When gfs2_freeze_lock_shared() fails after init_threads() succeeds, the
created kernel threads (logd and quotad) are never destroyed. This
occurs because the fail_per_node label doesn't call
gfs2_destroy_threads().
Second leak: quota bitmap buffer (8192 bytes)
When gfs2_make_fs_rw() fails after gfs2_quota_init() succeeds but
before other operations complete, the allocated quota bitmap is never
freed.
The fix moves thread cleanup to the fail_per_node label to handle all
error paths uniformly. gfs2_destroy_threads() is safe to call
unconditionally as it checks for NULL pointers. Quota cleanup is added
in gfs2_make_fs_rw() to properly handle the withdrawal case where
quota initialization succeeds but the filesystem is then withdrawn.
Thread leak backtrace (gfs2_freeze_lock_shared failure):
unreferenced object 0xffff88801d7bca80 (size 4480):
copy_process+0x3a1/0x4670 kernel/fork.c:2422
kernel_clone+0xf3/0x6e0 kernel/fork.c:2779
kthread_create_on_node+0x100/0x150 kernel/kthread.c:478
init_threads+0xab/0x350 fs/gfs2/ops_fstype.c:611
gfs2_fill_super+0xe5c/0x1240 fs/gfs2/ops_fstype.c:1265
Quota leak backtrace (gfs2_make_fs_rw failure):
unreferenced object 0xffff88812de7c000 (size 8192):
gfs2_quota_init+0xe5/0x820 fs/gfs2/quota.c:1409
gfs2_make_fs_rw+0x7a/0xe0 fs/gfs2/super.c:149
gfs2_fill_super+0xfbb/0x1240 fs/gfs2/ops_fstype.c:1275
In the Linux kernel, the following vulnerability has been resolved:
hfsplus: return error when node already exists in hfs_bnode_create
When hfs_bnode_create() finds that a node is already hashed (which should
not happen in normal operation), it currently returns the existing node
without incrementing its reference count. This causes a reference count
inconsistency that leads to a kernel panic when the node is later freed
in hfs_bnode_put():
kernel BUG at fs/hfsplus/bnode.c:676!
BUG_ON(!atomic_read(&node->refcnt))
This scenario can occur when hfs_bmap_alloc() attempts to allocate a node
that is already in use (e.g., when node 0's bitmap bit is incorrectly
unset), or due to filesystem corruption.
Returning an existing node from a create path is not normal operation.
Fix this by returning ERR_PTR(-EEXIST) instead of the node when it's
already hashed. This properly signals the error condition to callers,
which already check for IS_ERR() return values.
In the Linux kernel, the following vulnerability has been resolved:
fbdev: au1200fb: Fix a memory leak in au1200fb_drv_probe()
In au1200fb_drv_probe(), when platform_get_irq fails(), it directly
returns from the function with an error code, which causes a memory
leak.
Replace it with a goto label to ensure proper cleanup.
In the Linux kernel, the following vulnerability has been resolved:
md/raid5: fix IO hang with degraded array with llbitmap
When llbitmap bit state is still unwritten, any new write should force
rcw, as bitmap_ops->blocks_synced() is checked in handle_stripe_dirtying().
However, later the same check is missing in need_this_block(), causing
stripe to deadloop during handling because handle_stripe() will decide
to go to handle_stripe_fill(), meanwhile need_this_block() always return
0 and nothing is handled.
In the Linux kernel, the following vulnerability has been resolved:
eth: fbnic: Add validation for MTU changes
Increasing the MTU beyond the HDS threshold causes the hardware to
fragment packets across multiple buffers. If a single-buffer XDP program
is attached, the driver will drop all multi-frag frames. While we can't
prevent a remote sender from sending non-TCP packets larger than the MTU,
this will prevent users from inadvertently breaking new TCP streams.
Traditionally, drivers supported XDP with MTU less than 4Kb
(packet per page). Fbnic currently prevents attaching XDP when MTU is too high.
But it does not prevent increasing MTU after XDP is attached.
In the Linux kernel, the following vulnerability has been resolved:
crypto: starfive - Fix memory leak in starfive_aes_aead_do_one_req()
The starfive_aes_aead_do_one_req() function allocates rctx->adata with
kzalloc() but fails to free it if sg_copy_to_buffer() or
starfive_aes_hw_init() fails, which lead to memory leaks.
Since rctx->adata is unconditionally freed after the write_adata
operations, ensure consistent cleanup by freeing the allocation in these
earlier error paths as well.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
In the Linux kernel, the following vulnerability has been resolved:
hwrng: core - use RCU and work_struct to fix race condition
Currently, hwrng_fill is not cleared until the hwrng_fillfn() thread
exits. Since hwrng_unregister() reads hwrng_fill outside the rng_mutex
lock, a concurrent hwrng_unregister() may call kthread_stop() again on
the same task.
Additionally, if hwrng_unregister() is called immediately after
hwrng_register(), the stopped thread may have never been executed. Thus,
hwrng_fill remains dirty even after hwrng_unregister() returns. In this
case, subsequent calls to hwrng_register() will fail to start new
threads, and hwrng_unregister() will call kthread_stop() on the same
freed task. In both cases, a use-after-free occurs:
refcount_t: addition on 0; use-after-free.
WARNING: ... at lib/refcount.c:25 refcount_warn_saturate+0xec/0x1c0
Call Trace:
kthread_stop+0x181/0x360
hwrng_unregister+0x288/0x380
virtrng_remove+0xe3/0x200
This patch fixes the race by protecting the global hwrng_fill pointer
inside the rng_mutex lock, so that hwrng_fillfn() thread is stopped only
once, and calls to kthread_run() and kthread_stop() are serialized
with the lock held.
To avoid deadlock in hwrng_fillfn() while being stopped with the lock
held, we convert current_rng to RCU, so that get_current_rng() can read
current_rng without holding the lock. To remove the lock from put_rng(),
we also delay the actual cleanup into a work_struct.
Since get_current_rng() no longer returns ERR_PTR values, the IS_ERR()
checks are removed from its callers.
With hwrng_fill protected by the rng_mutex lock, hwrng_fillfn() can no
longer clear hwrng_fill itself. Therefore, if hwrng_fillfn() returns
directly after current_rng is dropped, kthread_stop() would be called on
a freed task_struct later. To fix this, hwrng_fillfn() calls schedule()
now to keep the task alive until being stopped. The kthread_stop() call
is also moved from hwrng_unregister() to drop_current_rng(), ensuring
kthread_stop() is called on all possible paths where current_rng becomes
NULL, so that the thread would not wait forever.
In the Linux kernel, the following vulnerability has been resolved:
ext4: fix memory leak in ext4_ext_shift_extents()
In ext4_ext_shift_extents(), if the extent is NULL in the while loop, the
function returns immediately without releasing the path obtained via
ext4_find_extent(), leading to a memory leak.
Fix this by jumping to the out label to ensure the path is properly
released.
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix memory leak in amdgpu_acpi_enumerate_xcc()
In amdgpu_acpi_enumerate_xcc(), if amdgpu_acpi_dev_init() returns -ENOMEM,
the function returns directly without releasing the allocated xcc_info,
resulting in a memory leak.
Fix this by ensuring that xcc_info is properly freed in the error paths.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Improper Following of a Certificate's Chain of Trust vulnerability in Erlang OTP public_key (pubkey_cert module) allows a non-CA certificate to be accepted as an intermediate issuer, enabling certificate chain forgery.
In lib/public_key/src/pubkey_cert.erl, pubkey_cert:validate_extensions/7 contains two flaws that together allow a certificate with basicConstraints cA:false and no keyUsage extension to be used as an intermediate issuer in a chain passed to public_key:pkix_path_validation/3: the cA:false clause recurses into the remaining extensions without rejecting the certificate when it is in issuer position, and the keyUsage check only fires when the extension is present, so a certificate lacking keyUsage entirely bypasses the keyCertSign enforcement.
Any party holding an end-entity certificate with basicConstraints cA:false and no keyUsage extension, issued by any CA in the victim's trust store, can use that certificate's private key to sign forged leaf certificates for arbitrary identities. public_key:pkix_path_validation/3 accepts the resulting chain, and by extension every TLS or mTLS endpoint built on the OTP ssl application that relies on the default verifier is affected, including server identity verification on the client side and client certificate verification on mTLS servers.
This issue affects OTP from OTP 17.0 before OTP 26.2.5.21, 27.3.4.12, 28.5.0.1, and 29.0.1 corresponding to public_key from 0.22 before 1.15.1.7, 1.17.1.3, 1.20.3.1, and 1.21.1.
IBM Cloud APM, Base Private 8.1.4 and IBM Cloud APM, Advanced Private 8.1.4 IBM Db2 for Linux, UNIX and Windows (includes DB2 Connect Server) could allow an authenticated user to cause a denial of service due to improper neutralization of special elements in the data query logic of the Fenced environment.
A flaw was found in Samba’s vfs_worm module. The module is intended to provide write-once, read-many (WORM) protections by preventing modification of files after a configurable grace period. Due to insufficient validation during rename operations, an authenticated user with write access to a share could overwrite a protected file by renaming a newly created file over the existing WORM-protected file.
libusb before version 1.0.30 contains a NULL pointer dereference vulnerability that allows attackers to crash applications by supplying a malformed USB configuration descriptor where an interface claims bNumEndpoints greater than zero but is followed by a class-specific descriptor whose bLength exceeds the remaining buffer size, causing parse_interface() to return early without allocating the endpoint array. Attackers can exploit this flaw through libusb_get_active_config_descriptor or libusb_get_config_descriptor by providing crafted descriptors via virtualized USB passthrough, file-based descriptor parsing, or network sources, causing any application iterating over endpoints to dereference a NULL endpoint pointer and crash.
IBM Cognos Analytics 11.2.0, 11.2.4, 12.0, and 12.1.0 and IBM Cognos Transformer 11.2.4, 12.0, and 12.1.0 are vulnerable to cross-site scripting (XSS). This vulnerability allows a remote attacker to inject arbitrary JavaScript code into the web user interface, which may alter the intended functionality and could lead to the disclosure of credentials within a trusted session.
IBM Operations Analytics - Log Analysis 1.3.5.0, 1.3.5.1, 1.3.5.2, 1.3.5.3, 1.3.6.0, 1.3.6.1, 1.3.7.0, 1.3.7.1, 1.3.7.2, and 1.3.8.0, 1.3.8.1, 1.3.8.2, 1.3.8.3, 1.3.8.4 IBM SmartCloud Analytics - Log Analysis does not require that users should have strong passwords by default, which makes it easier for attackers to compromise user accounts.
IBM SDI 7.2.0.0 through 7.2.0.14 and IBM Security Directory Integrator 10.0.0.0 through 10.0.0.2 could allow a remote attacker to obtain sensitive information when a detailed technical error message is returned in the browser. This information could be used in further attacks against the system.
A flaw was found in Keycloak, an open-source identity and access management solution. When a client application is configured to accept broad redirect Uniform Resource Identifiers (URIs), a remote attacker can manipulate the authentication process by crafting a special web address. If a user clicks this link, the client application might incorrectly prioritize attacker-controlled information over legitimate data. This vulnerability, known as HTTP parameter pollution, could allow an attacker to bypass security measures or gain unauthorized access to resources.
Improper Neutralization of Input During Web Page Generation ('Cross-site Scripting') vulnerability in wpdevelop Booking Manager booking-manager allows Stored XSS.This issue affects Booking Manager: from n/a through <= 2.1.18.
Improper Neutralization of Input During Web Page Generation ('Cross-site Scripting') vulnerability in Nexcess WPComplete wpcomplete allows Stored XSS.This issue affects WPComplete: from n/a through <= 2.9.5.4.
Improper Validation of Specified Quantity in Input vulnerability in Ads by WPQuads Ads by WPQuads quick-adsense-reloaded allows Manipulating Hidden Fields.This issue affects Ads by WPQuads: from n/a through <= 3.0.2.
Improper Validation of Specified Quantity in Input vulnerability in Ads by WPQuads Ads by WPQuads quick-adsense-reloaded allows Input Data Manipulation.This issue affects Ads by WPQuads: from n/a through <= 3.0.2.
Authorization Bypass Through User-Controlled Key vulnerability in WP Wham Checkout Files Upload for WooCommerce checkout-files-upload-woocommerce allows Exploiting Incorrectly Configured Access Control Security Levels.This issue affects Checkout Files Upload for WooCommerce: from n/a through <= 2.2.5.
The MinhNhut Link Gateway plugin for WordPress is vulnerable to Reflected Cross-Site Scripting via the 'url' parameter on the redirect page in all versions up to, and including, 3.6.1 due to insufficient input sanitization and output escaping. This makes it possible for unauthenticated attackers to inject arbitrary web scripts in pages that execute if they can successfully trick a user into performing an action such as clicking on a link.
The MinhNhut Link Gateway plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the plugin's settings (Description, Title, and other fields) in all versions up to, and including, 3.6.1 due to insufficient input sanitization and output escaping. This makes it possible for authenticated attackers, with Administrator-level access and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses the redirect page. This only affects multi-site installations and installations where unfiltered_html has been disabled.
The myLinksDump plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the 'link_title' parameter in all versions up to, and including, 1.6 due to insufficient input sanitization and output escaping. This makes it possible for authenticated attackers, with administrator-level access and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page. This only affects multi-site installations and installations where unfiltered_html has been disabled.
The rexCrawler plugin for WordPress is vulnerable to Stored Cross-Site Scripting via admin settings in all versions up to, and including, 1.0.15 due to insufficient input sanitization and output escaping. This makes it possible for authenticated attackers, with administrator-level permissions and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page. This only affects multi-site installations and installations where unfiltered_html has been disabled.
The Xpro Elementor Addons - Pro plugin for WordPress is vulnerable to Arbitrary File Reading in all versions up to, and including, 1.4.7 via the Draw SVG widget. This makes it possible for authenticated attackers, with Contributor-level access and above, to read the contents of arbitrary files on the server, which can contain sensitive information.
Improper Neutralization of Input During Web Page Generation ('Cross-site Scripting') vulnerability in Averta Master Slider allows DOM-Based XSS.
This issue affects Master Slider: from n/a through 3.10.8.
Insertion of Sensitive Information Into Sent Data vulnerability in Tom GenerateBlocks allows Retrieve Embedded Sensitive Data.
This issue affects GenerateBlocks: from n/a through 2.1.0.
An low privileged remote attacker can exploit an unauthenticated SQL Injection vulnerability in the user_alarmprofile view due to improper neutralization of special elements in a SQL SELECT command. This can result in a total loss of confidentiality.
An low privileged remote attacker can exploit an unauthenticated SQL Injection vulnerability in the tag view due to improper neutralization of special elements in a SQL SELECT command. This can result in a total loss of confidentiality.
An low privileged remote attacker can exploit an unauthenticated SQL Injection vulnerability in the system_tag view due to improper neutralization of special elements in a SQL SELECT command. This can result in a total loss of confidentiality.
An low privileged remote attacker can exploit an unauthenticated SQL Injection vulnerability in the system view due to improper neutralization of special elements in a SQL SELECT command. This can result in a total loss of confidentiality.
An low privileged remote attacker can exploit an unauthenticated SQL Injection vulnerability in the devices_configuration view due to improper neutralization of special elements in a SQL SELECT command. This can result in a total loss of confidentiality.