In the Linux kernel, the following vulnerability has been resolved:
ALSA: emux: improve patch ioctl data validation
In load_data(), make the validation of and skipping over the main info
block match that in load_guspatch().
In load_guspatch(), add checking that the specified patch length matches
the actually supplied data, like load_data() already did.
In the Linux kernel, the following vulnerability has been resolved:
x86: stop playing stack games in profile_pc()
The 'profile_pc()' function is used for timer-based profiling, which
isn't really all that relevant any more to begin with, but it also ends
up making assumptions based on the stack layout that aren't necessarily
valid.
Basically, the code tries to account the time spent in spinlocks to the
caller rather than the spinlock, and while I support that as a concept,
it's not worth the code complexity or the KASAN warnings when no serious
profiling is done using timers anyway these days.
And the code really does depend on stack layout that is only true in the
simplest of cases. We've lost the comment at some point (I think when
the 32-bit and 64-bit code was unified), but it used to say:
Assume the lock function has either no stack frame or a copy
of eflags from PUSHF.
which explains why it just blindly loads a word or two straight off the
stack pointer and then takes a minimal look at the values to just check
if they might be eflags or the return pc:
Eflags always has bits 22 and up cleared unlike kernel addresses
but that basic stack layout assumption assumes that there isn't any lock
debugging etc going on that would complicate the code and cause a stack
frame.
It causes KASAN unhappiness reported for years by syzkaller [1] and
others [2].
With no real practical reason for this any more, just remove the code.
Just for historical interest, here's some background commits relating to
this code from 2006:
0cb91a229364 ("i386: Account spinlocks to the caller during profiling for !FP kernels")
31679f38d886 ("Simplify profile_pc on x86-64")
and a code unification from 2009:
ef4512882dbe ("x86: time_32/64.c unify profile_pc")
but the basics of this thing actually goes back to before the git tree.
In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_omap: Implementation of Errata i2310
As per Errata i2310[0], Erroneous timeout can be triggered,
if this Erroneous interrupt is not cleared then it may leads
to storm of interrupts, therefore apply Errata i2310 solution.
[0] https://www.ti.com/lit/pdf/sprz536 page 23
In the Linux kernel, the following vulnerability has been resolved:
net/iucv: Avoid explicit cpumask var allocation on stack
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it.
In the Linux kernel, the following vulnerability has been resolved:
net/dpaa2: Avoid explicit cpumask var allocation on stack
For CONFIG_CPUMASK_OFFSTACK=y kernel, explicit allocation of cpumask
variable on stack is not recommended since it can cause potential stack
overflow.
Instead, kernel code should always use *cpumask_var API(s) to allocate
cpumask var in config-neutral way, leaving allocation strategy to
CONFIG_CPUMASK_OFFSTACK.
Use *cpumask_var API(s) to address it.
In the Linux kernel, the following vulnerability has been resolved:
gpio: davinci: Validate the obtained number of IRQs
Value of pdata->gpio_unbanked is taken from Device Tree. In case of broken
DT due to any error this value can be any. Without this value validation
there can be out of chips->irqs array boundaries access in
davinci_gpio_probe().
Validate the obtained nirq value so that it won't exceed the maximum
number of IRQs per bank.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Check pat.ops before dumping PAT settings
We may leave pat.ops unset when running on brand new platform or
when running as a VF. While the former is unlikely, the latter
is valid (future) use case and will cause NPD when someone will
try to dump PAT settings by debugfs.
It's better to check pointer to pat.ops instead of specific .dump
hook, as we have this hook always defined for every .ops variant.
In the Linux kernel, the following vulnerability has been resolved:
pinctrl: fix deadlock in create_pinctrl() when handling -EPROBE_DEFER
In create_pinctrl(), pinctrl_maps_mutex is acquired before calling
add_setting(). If add_setting() returns -EPROBE_DEFER, create_pinctrl()
calls pinctrl_free(). However, pinctrl_free() attempts to acquire
pinctrl_maps_mutex, which is already held by create_pinctrl(), leading to
a potential deadlock.
This patch resolves the issue by releasing pinctrl_maps_mutex before
calling pinctrl_free(), preventing the deadlock.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
In the Linux kernel, the following vulnerability has been resolved:
ASoC: fsl-asoc-card: set priv->pdev before using it
priv->pdev pointer was set after being used in
fsl_asoc_card_audmux_init().
Move this assignment at the start of the probe function, so
sub-functions can correctly use pdev through priv.
fsl_asoc_card_audmux_init() dereferences priv->pdev to get access to the
dev struct, used with dev_err macros.
As priv is zero-initialised, there would be a NULL pointer dereference.
Note that if priv->dev is dereferenced before assignment but never used,
for example if there is no error to be printed, the driver won't crash
probably due to compiler optimisations.
In the Linux kernel, the following vulnerability has been resolved:
drm/panel: ilitek-ili9881c: Fix warning with GPIO controllers that sleep
The ilitek-ili9881c controls the reset GPIO using the non-sleeping
gpiod_set_value() function. This complains loudly when the GPIO
controller needs to sleep. As the caller can sleep, use
gpiod_set_value_cansleep() to fix the issue.
In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: bme680: Fix overflows in compensate() functions
There are cases in the compensate functions of the driver that
there could be overflows of variables due to bit shifting ops.
These implications were initially discussed here [1] and they
were mentioned in log message of Commit 1b3bd8592780 ("iio:
chemical: Add support for Bosch BME680 sensor").
[1]: https://lore.kernel.org/linux-iio/20180728114028.3c1bbe81@archlinux/
In the Linux kernel, the following vulnerability has been resolved:
usb: dwc3: core: remove lock of otg mode during gadget suspend/resume to avoid deadlock
When config CONFIG_USB_DWC3_DUAL_ROLE is selected, and trigger system
to enter suspend status with below command:
echo mem > /sys/power/state
There will be a deadlock issue occurring. Detailed invoking path as
below:
dwc3_suspend_common()
spin_lock_irqsave(&dwc->lock, flags); <-- 1st
dwc3_gadget_suspend(dwc);
dwc3_gadget_soft_disconnect(dwc);
spin_lock_irqsave(&dwc->lock, flags); <-- 2nd
This issue is exposed by commit c7ebd8149ee5 ("usb: dwc3: gadget: Fix
NULL pointer dereference in dwc3_gadget_suspend") that removes the code
of checking whether dwc->gadget_driver is NULL or not. It causes the
following code is executed and deadlock occurs when trying to get the
spinlock. In fact, the root cause is the commit 5265397f9442("usb: dwc3:
Remove DWC3 locking during gadget suspend/resume") that forgot to remove
the lock of otg mode. So, remove the redundant lock of otg mode during
gadget suspend/resume.
In the Linux kernel, the following vulnerability has been resolved:
ftruncate: pass a signed offset
The old ftruncate() syscall, using the 32-bit off_t misses a sign
extension when called in compat mode on 64-bit architectures. As a
result, passing a negative length accidentally succeeds in truncating
to file size between 2GiB and 4GiB.
Changing the type of the compat syscall to the signed compat_off_t
changes the behavior so it instead returns -EINVAL.
The native entry point, the truncate() syscall and the corresponding
loff_t based variants are all correct already and do not suffer
from this mistake.
In the Linux kernel, the following vulnerability has been resolved:
xdp: Remove WARN() from __xdp_reg_mem_model()
syzkaller reports a warning in __xdp_reg_mem_model().
The warning occurs only if __mem_id_init_hash_table() returns an error. It
returns the error in two cases:
1. memory allocation fails;
2. rhashtable_init() fails when some fields of rhashtable_params
struct are not initialized properly.
The second case cannot happen since there is a static const rhashtable_params
struct with valid fields. So, warning is only triggered when there is a
problem with memory allocation.
Thus, there is no sense in using WARN() to handle this error and it can be
safely removed.
WARNING: CPU: 0 PID: 5065 at net/core/xdp.c:299 __xdp_reg_mem_model+0x2d9/0x650 net/core/xdp.c:299
CPU: 0 PID: 5065 Comm: syz-executor883 Not tainted 6.8.0-syzkaller-05271-gf99c5f563c17 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024
RIP: 0010:__xdp_reg_mem_model+0x2d9/0x650 net/core/xdp.c:299
Call Trace:
xdp_reg_mem_model+0x22/0x40 net/core/xdp.c:344
xdp_test_run_setup net/bpf/test_run.c:188 [inline]
bpf_test_run_xdp_live+0x365/0x1e90 net/bpf/test_run.c:377
bpf_prog_test_run_xdp+0x813/0x11b0 net/bpf/test_run.c:1267
bpf_prog_test_run+0x33a/0x3b0 kernel/bpf/syscall.c:4240
__sys_bpf+0x48d/0x810 kernel/bpf/syscall.c:5649
__do_sys_bpf kernel/bpf/syscall.c:5738 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5736 [inline]
__x64_sys_bpf+0x7c/0x90 kernel/bpf/syscall.c:5736
do_syscall_64+0xfb/0x240
entry_SYSCALL_64_after_hwframe+0x6d/0x75
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
In the Linux kernel, the following vulnerability has been resolved:
RDMA/restrack: Fix potential invalid address access
struct rdma_restrack_entry's kern_name was set to KBUILD_MODNAME
in ib_create_cq(), while if the module exited but forgot del this
rdma_restrack_entry, it would cause a invalid address access in
rdma_restrack_clean() when print the owner of this rdma_restrack_entry.
These code is used to help find one forgotten PD release in one of the
ULPs. But it is not needed anymore, so delete them.
In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix DIO failure due to insufficient transaction credits
The code in ocfs2_dio_end_io_write() estimates number of necessary
transaction credits using ocfs2_calc_extend_credits(). This however does
not take into account that the IO could be arbitrarily large and can
contain arbitrary number of extents.
Extent tree manipulations do often extend the current transaction but not
in all of the cases. For example if we have only single block extents in
the tree, ocfs2_mark_extent_written() will end up calling
ocfs2_replace_extent_rec() all the time and we will never extend the
current transaction and eventually exhaust all the transaction credits if
the IO contains many single block extents. Once that happens a
WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in
jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to
this error. This was actually triggered by one of our customers on a
heavily fragmented OCFS2 filesystem.
To fix the issue make sure the transaction always has enough credits for
one extent insert before each call of ocfs2_mark_extent_written().
Heming Zhao said:
------
PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error"
PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA"
#0 machine_kexec at ffffffff8c069932
#1 __crash_kexec at ffffffff8c1338fa
#2 panic at ffffffff8c1d69b9
#3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2]
#4 __ocfs2_abort at ffffffffc0c88387 [ocfs2]
#5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2]
#6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2]
#7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2]
#8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2]
#9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2]
#10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2]
#11 dio_complete at ffffffff8c2b9fa7
#12 do_blockdev_direct_IO at ffffffff8c2bc09f
#13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2]
#14 generic_file_direct_write at ffffffff8c1dcf14
#15 __generic_file_write_iter at ffffffff8c1dd07b
#16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2]
#17 aio_write at ffffffff8c2cc72e
#18 kmem_cache_alloc at ffffffff8c248dde
#19 do_io_submit at ffffffff8c2ccada
#20 do_syscall_64 at ffffffff8c004984
#21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba
In the Linux kernel, the following vulnerability has been resolved:
mlxsw: spectrum_buffers: Fix memory corruptions on Spectrum-4 systems
The following two shared buffer operations make use of the Shared Buffer
Status Register (SBSR):
# devlink sb occupancy snapshot pci/0000:01:00.0
# devlink sb occupancy clearmax pci/0000:01:00.0
The register has two masks of 256 bits to denote on which ingress /
egress ports the register should operate on. Spectrum-4 has more than
256 ports, so the register was extended by cited commit with a new
'port_page' field.
However, when filling the register's payload, the driver specifies the
ports as absolute numbers and not relative to the first port of the port
page, resulting in memory corruptions [1].
Fix by specifying the ports relative to the first port of the port page.
[1]
BUG: KASAN: slab-use-after-free in mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
Read of size 1 at addr ffff8881068cb00f by task devlink/1566
[...]
Call Trace:
<TASK>
dump_stack_lvl+0xc6/0x120
print_report+0xce/0x670
kasan_report+0xd7/0x110
mlxsw_sp_sb_occ_snapshot+0xb6d/0xbc0
mlxsw_devlink_sb_occ_snapshot+0x75/0xb0
devlink_nl_sb_occ_snapshot_doit+0x1f9/0x2a0
genl_family_rcv_msg_doit+0x20c/0x300
genl_rcv_msg+0x567/0x800
netlink_rcv_skb+0x170/0x450
genl_rcv+0x2d/0x40
netlink_unicast+0x547/0x830
netlink_sendmsg+0x8d4/0xdb0
__sys_sendto+0x49b/0x510
__x64_sys_sendto+0xe5/0x1c0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
Allocated by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
__kasan_kmalloc+0x8f/0xa0
copy_verifier_state+0xbc2/0xfb0
do_check_common+0x2c51/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 1:
kasan_save_stack+0x33/0x60
kasan_save_track+0x14/0x30
kasan_save_free_info+0x3b/0x60
poison_slab_object+0x109/0x170
__kasan_slab_free+0x14/0x30
kfree+0xca/0x2b0
free_verifier_state+0xce/0x270
do_check_common+0x4828/0xc7e0
bpf_check+0x5107/0x9960
bpf_prog_load+0xf0e/0x2690
__sys_bpf+0x1a61/0x49d0
__x64_sys_bpf+0x7d/0xc0
do_syscall_64+0xc1/0x1d0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers
register store validation for NFT_DATA_VALUE is conditional, however,
the datatype is always either NFT_DATA_VALUE or NFT_DATA_VERDICT. This
only requires a new helper function to infer the register type from the
set datatype so this conditional check can be removed. Otherwise,
pointer to chain object can be leaked through the registers.
In the Linux kernel, the following vulnerability has been resolved:
net: mana: Fix possible double free in error handling path
When auxiliary_device_add() returns error and then calls
auxiliary_device_uninit(), callback function adev_release
calls kfree(madev). We shouldn't call kfree(madev) again
in the error handling path. Set 'madev' to NULL.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Take return from set_memory_ro() into account with bpf_prog_lock_ro()
set_memory_ro() can fail, leaving memory unprotected.
Check its return and take it into account as an error.
In the Linux kernel, the following vulnerability has been resolved:
bpf: Mark bpf prog stack with kmsan_unposion_memory in interpreter mode
syzbot reported uninit memory usages during map_{lookup,delete}_elem.
==========
BUG: KMSAN: uninit-value in __dev_map_lookup_elem kernel/bpf/devmap.c:441 [inline]
BUG: KMSAN: uninit-value in dev_map_lookup_elem+0xf3/0x170 kernel/bpf/devmap.c:796
__dev_map_lookup_elem kernel/bpf/devmap.c:441 [inline]
dev_map_lookup_elem+0xf3/0x170 kernel/bpf/devmap.c:796
____bpf_map_lookup_elem kernel/bpf/helpers.c:42 [inline]
bpf_map_lookup_elem+0x5c/0x80 kernel/bpf/helpers.c:38
___bpf_prog_run+0x13fe/0xe0f0 kernel/bpf/core.c:1997
__bpf_prog_run256+0xb5/0xe0 kernel/bpf/core.c:2237
==========
The reproducer should be in the interpreter mode.
The C reproducer is trying to run the following bpf prog:
0: (18) r0 = 0x0
2: (18) r1 = map[id:49]
4: (b7) r8 = 16777216
5: (7b) *(u64 *)(r10 -8) = r8
6: (bf) r2 = r10
7: (07) r2 += -229
^^^^^^^^^^
8: (b7) r3 = 8
9: (b7) r4 = 0
10: (85) call dev_map_lookup_elem#1543472
11: (95) exit
It is due to the "void *key" (r2) passed to the helper. bpf allows uninit
stack memory access for bpf prog with the right privileges. This patch
uses kmsan_unpoison_memory() to mark the stack as initialized.
This should address different syzbot reports on the uninit "void *key"
argument during map_{lookup,delete}_elem.
ImageMagick is a free and open-source software suite, used for editing and manipulating digital images. The `AppImage` version `ImageMagick` might use an empty path when setting `MAGICK_CONFIGURE_PATH` and `LD_LIBRARY_PATH` environment variables while executing, which might lead to arbitrary code execution by loading malicious configuration files or shared libraries in the current working directory while executing `ImageMagick`. The vulnerability is fixed in 7.11-36.
Twisted is an event-based framework for internet applications, supporting Python 3.6+. The `twisted.web.util.redirectTo` function contains an HTML injection vulnerability. If application code allows an attacker to control the redirect URL this vulnerability may result in Reflected Cross-Site Scripting (XSS) in the redirect response HTML body. This vulnerability is fixed in 24.7.0rc1.
In the Linux kernel, the following vulnerability has been resolved:
usb: atm: cxacru: fix endpoint checking in cxacru_bind()
Syzbot is still reporting quite an old issue [1] that occurs due to
incomplete checking of present usb endpoints. As such, wrong
endpoints types may be used at urb sumbitting stage which in turn
triggers a warning in usb_submit_urb().
Fix the issue by verifying that required endpoint types are present
for both in and out endpoints, taking into account cmd endpoint type.
Unfortunately, this patch has not been tested on real hardware.
[1] Syzbot report:
usb 1-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 0 PID: 8667 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 0 PID: 8667 Comm: kworker/0:4 Not tainted 5.14.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
...
Call Trace:
cxacru_cm+0x3c0/0x8e0 drivers/usb/atm/cxacru.c:649
cxacru_card_status+0x22/0xd0 drivers/usb/atm/cxacru.c:760
cxacru_bind+0x7ac/0x11a0 drivers/usb/atm/cxacru.c:1209
usbatm_usb_probe+0x321/0x1ae0 drivers/usb/atm/usbatm.c:1055
cxacru_usb_probe+0xdf/0x1e0 drivers/usb/atm/cxacru.c:1363
usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:517 [inline]
really_probe+0x23c/0xcd0 drivers/base/dd.c:595
__driver_probe_device+0x338/0x4d0 drivers/base/dd.c:747
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:777
__device_attach_driver+0x20b/0x2f0 drivers/base/dd.c:894
bus_for_each_drv+0x15f/0x1e0 drivers/base/bus.c:427
__device_attach+0x228/0x4a0 drivers/base/dd.c:965
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:487
device_add+0xc2f/0x2180 drivers/base/core.c:3354
usb_set_configuration+0x113a/0x1910 drivers/usb/core/message.c:2170
usb_generic_driver_probe+0xba/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd9/0x2c0 drivers/usb/core/driver.c:293
In the Linux kernel, the following vulnerability has been resolved:
PCI/MSI: Fix UAF in msi_capability_init
KFENCE reports the following UAF:
BUG: KFENCE: use-after-free read in __pci_enable_msi_range+0x2c0/0x488
Use-after-free read at 0x0000000024629571 (in kfence-#12):
__pci_enable_msi_range+0x2c0/0x488
pci_alloc_irq_vectors_affinity+0xec/0x14c
pci_alloc_irq_vectors+0x18/0x28
kfence-#12: 0x0000000008614900-0x00000000e06c228d, size=104, cache=kmalloc-128
allocated by task 81 on cpu 7 at 10.808142s:
__kmem_cache_alloc_node+0x1f0/0x2bc
kmalloc_trace+0x44/0x138
msi_alloc_desc+0x3c/0x9c
msi_domain_insert_msi_desc+0x30/0x78
msi_setup_msi_desc+0x13c/0x184
__pci_enable_msi_range+0x258/0x488
pci_alloc_irq_vectors_affinity+0xec/0x14c
pci_alloc_irq_vectors+0x18/0x28
freed by task 81 on cpu 7 at 10.811436s:
msi_domain_free_descs+0xd4/0x10c
msi_domain_free_locked.part.0+0xc0/0x1d8
msi_domain_alloc_irqs_all_locked+0xb4/0xbc
pci_msi_setup_msi_irqs+0x30/0x4c
__pci_enable_msi_range+0x2a8/0x488
pci_alloc_irq_vectors_affinity+0xec/0x14c
pci_alloc_irq_vectors+0x18/0x28
Descriptor allocation done in:
__pci_enable_msi_range
msi_capability_init
msi_setup_msi_desc
msi_insert_msi_desc
msi_domain_insert_msi_desc
msi_alloc_desc
...
Freed in case of failure in __msi_domain_alloc_locked()
__pci_enable_msi_range
msi_capability_init
pci_msi_setup_msi_irqs
msi_domain_alloc_irqs_all_locked
msi_domain_alloc_locked
__msi_domain_alloc_locked => fails
msi_domain_free_locked
...
That failure propagates back to pci_msi_setup_msi_irqs() in
msi_capability_init() which accesses the descriptor for unmasking in the
error exit path.
Cure it by copying the descriptor and using the copy for the error exit path
unmask operation.
[ tglx: Massaged change log ]
In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_ld_modes
In nv17_tv_get_ld_modes(), the return value of drm_mode_duplicate() is
assigned to mode, which will lead to a possible NULL pointer dereference
on failure of drm_mode_duplicate(). Add a check to avoid npd.
In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: avoid using null object of framebuffer
Instead of using state->fb->obj[0] directly, get object from framebuffer
by calling drm_gem_fb_get_obj() and return error code when object is
null to avoid using null object of framebuffer.
In the Linux kernel, the following vulnerability has been resolved:
drm/i915/gt: Fix potential UAF by revoke of fence registers
CI has been sporadically reporting the following issue triggered by
igt@i915_selftest@live@hangcheck on ADL-P and similar machines:
<6> [414.049203] i915: Running intel_hangcheck_live_selftests/igt_reset_evict_fence
...
<6> [414.068804] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled
<6> [414.068812] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled
<3> [414.070354] Unable to pin Y-tiled fence; err:-4
<3> [414.071282] i915_vma_revoke_fence:301 GEM_BUG_ON(!i915_active_is_idle(&fence->active))
...
<4>[ 609.603992] ------------[ cut here ]------------
<2>[ 609.603995] kernel BUG at drivers/gpu/drm/i915/gt/intel_ggtt_fencing.c:301!
<4>[ 609.604003] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
<4>[ 609.604006] CPU: 0 PID: 268 Comm: kworker/u64:3 Tainted: G U W 6.9.0-CI_DRM_14785-g1ba62f8cea9c+ #1
<4>[ 609.604008] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR4 RVP, BIOS RPLPFWI1.R00.4035.A00.2301200723 01/20/2023
<4>[ 609.604010] Workqueue: i915 __i915_gem_free_work [i915]
<4>[ 609.604149] RIP: 0010:i915_vma_revoke_fence+0x187/0x1f0 [i915]
...
<4>[ 609.604271] Call Trace:
<4>[ 609.604273] <TASK>
...
<4>[ 609.604716] __i915_vma_evict+0x2e9/0x550 [i915]
<4>[ 609.604852] __i915_vma_unbind+0x7c/0x160 [i915]
<4>[ 609.604977] force_unbind+0x24/0xa0 [i915]
<4>[ 609.605098] i915_vma_destroy+0x2f/0xa0 [i915]
<4>[ 609.605210] __i915_gem_object_pages_fini+0x51/0x2f0 [i915]
<4>[ 609.605330] __i915_gem_free_objects.isra.0+0x6a/0xc0 [i915]
<4>[ 609.605440] process_scheduled_works+0x351/0x690
...
In the past, there were similar failures reported by CI from other IGT
tests, observed on other platforms.
Before commit 63baf4f3d587 ("drm/i915/gt: Only wait for GPU activity
before unbinding a GGTT fence"), i915_vma_revoke_fence() was waiting for
idleness of vma->active via fence_update(). That commit introduced
vma->fence->active in order for the fence_update() to be able to wait
selectively on that one instead of vma->active since only idleness of
fence registers was needed. But then, another commit 0d86ee35097a
("drm/i915/gt: Make fence revocation unequivocal") replaced the call to
fence_update() in i915_vma_revoke_fence() with only fence_write(), and
also added that GEM_BUG_ON(!i915_active_is_idle(&fence->active)) in front.
No justification was provided on why we might then expect idleness of
vma->fence->active without first waiting on it.
The issue can be potentially caused by a race among revocation of fence
registers on one side and sequential execution of signal callbacks invoked
on completion of a request that was using them on the other, still
processed in parallel to revocation of those fence registers. Fix it by
waiting for idleness of vma->fence->active in i915_vma_revoke_fence().
(cherry picked from commit 24bb052d3dd499c5956abad5f7d8e4fd07da7fb1)
In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau/dispnv04: fix null pointer dereference in nv17_tv_get_hd_modes
In nv17_tv_get_hd_modes(), the return value of drm_mode_duplicate() is
assigned to mode, which will lead to a possible NULL pointer dereference
on failure of drm_mode_duplicate(). The same applies to drm_cvt_mode().
Add a check to avoid null pointer dereference.
In the Linux kernel, the following vulnerability has been resolved:
can: mcp251xfd: fix infinite loop when xmit fails
When the mcp251xfd_start_xmit() function fails, the driver stops
processing messages, and the interrupt routine does not return,
running indefinitely even after killing the running application.
Error messages:
[ 441.298819] mcp251xfd spi2.0 can0: ERROR in mcp251xfd_start_xmit: -16
[ 441.306498] mcp251xfd spi2.0 can0: Transmit Event FIFO buffer not empty. (seq=0x000017c7, tef_tail=0x000017cf, tef_head=0x000017d0, tx_head=0x000017d3).
... and repeat forever.
The issue can be triggered when multiple devices share the same SPI
interface. And there is concurrent access to the bus.
The problem occurs because tx_ring->head increments even if
mcp251xfd_start_xmit() fails. Consequently, the driver skips one TX
package while still expecting a response in
mcp251xfd_handle_tefif_one().
Resolve the issue by starting a workqueue to write the tx obj
synchronously if err = -EBUSY. In case of another error, decrement
tx_ring->head, remove skb from the echo stack, and drop the message.
[mkl: use more imperative wording in patch description]
In the Linux kernel, the following vulnerability has been resolved:
bcachefs: Fix sb_field_downgrade validation
- bch2_sb_downgrade_validate() wasn't checking for a downgrade entry
extending past the end of the superblock section
- for_each_downgrade_entry() is used in to_text() and needs to work on
malformed input; it also was missing a check for a field extending
past the end of the section
In the Linux kernel, the following vulnerability has been resolved:
net: can: j1939: enhanced error handling for tightly received RTS messages in xtp_rx_rts_session_new
This patch enhances error handling in scenarios with RTS (Request to
Send) messages arriving closely. It replaces the less informative WARN_ON_ONCE
backtraces with a new error handling method. This provides clearer error
messages and allows for the early termination of problematic sessions.
Previously, sessions were only released at the end of j1939_xtp_rx_rts().
Potentially this could be reproduced with something like:
testj1939 -r vcan0:0x80 &
while true; do
# send first RTS
cansend vcan0 18EC8090#1014000303002301;
# send second RTS
cansend vcan0 18EC8090#1014000303002301;
# send abort
cansend vcan0 18EC8090#ff00000000002301;
done
Twisted is an event-based framework for internet applications, supporting Python 3.6+. The HTTP 1.0 and 1.1 server provided by twisted.web could process pipelined HTTP requests out-of-order, possibly resulting in information disclosure. This vulnerability is fixed in 24.7.0rc1.
In the Linux kernel, the following vulnerability has been resolved:
nvme-fabrics: use reserved tag for reg read/write command
In some scenarios, if too many commands are issued by nvme command in
the same time by user tasks, this may exhaust all tags of admin_q. If
a reset (nvme reset or IO timeout) occurs before these commands finish,
reconnect routine may fail to update nvme regs due to insufficient tags,
which will cause kernel hang forever. In order to workaround this issue,
maybe we can let reg_read32()/reg_read64()/reg_write32() use reserved
tags. This maybe safe for nvmf:
1. For the disable ctrl path, we will not issue connect command
2. For the enable ctrl / fw activate path, since connect and reg_xx()
are called serially.
So the reserved tags may still be enough while reg_xx() use reserved tags.
In the Linux kernel, the following vulnerability has been resolved:
ila: block BH in ila_output()
As explained in commit 1378817486d6 ("tipc: block BH
before using dst_cache"), net/core/dst_cache.c
helpers need to be called with BH disabled.
ila_output() is called from lwtunnel_output()
possibly from process context, and under rcu_read_lock().
We might be interrupted by a softirq, re-enter ila_output()
and corrupt dst_cache data structures.
Fix the race by using local_bh_disable().
In the Linux kernel, the following vulnerability has been resolved:
io_uring: fix possible deadlock in io_register_iowq_max_workers()
The io_register_iowq_max_workers() function calls io_put_sq_data(),
which acquires the sqd->lock without releasing the uring_lock.
Similar to the commit 009ad9f0c6ee ("io_uring: drop ctx->uring_lock
before acquiring sqd->lock"), this can lead to a potential deadlock
situation.
To resolve this issue, the uring_lock is released before calling
io_put_sq_data(), and then it is re-acquired after the function call.
This change ensures that the locks are acquired in the correct
order, preventing the possibility of a deadlock.
In the Linux kernel, the following vulnerability has been resolved:
nvmet: always initialize cqe.result
The spec doesn't mandate that the first two double words (aka results)
for the command queue entry need to be set to 0 when they are not
used (not specified). Though, the target implemention returns 0 for TCP
and FC but not for RDMA.
Let's make RDMA behave the same and thus explicitly initializing the
result field. This prevents leaking any data from the stack.
In the Linux kernel, the following vulnerability has been resolved:
btrfs: qgroup: fix quota root leak after quota disable failure
If during the quota disable we fail when cleaning the quota tree or when
deleting the root from the root tree, we jump to the 'out' label without
ever dropping the reference on the quota root, resulting in a leak of the
root since fs_info->quota_root is no longer pointing to the root (we have
set it to NULL just before those steps).
Fix this by always doing a btrfs_put_root() call under the 'out' label.
This is a problem that exists since qgroups were first added in 2012 by
commit bed92eae26cc ("Btrfs: qgroup implementation and prototypes"), but
back then we missed a kfree on the quota root and free_extent_buffer()
calls on its root and commit root nodes, since back then roots were not
yet reference counted.
In the Linux kernel, the following vulnerability has been resolved:
null_blk: fix validation of block size
Block size should be between 512 and PAGE_SIZE and be a power of 2. The current
check does not validate this, so update the check.
Without this patch, null_blk would Oops due to a null pointer deref when
loaded with bs=1536 [1].
[axboe: remove unnecessary braces and != 0 check]
In the Linux kernel, the following vulnerability has been resolved:
NFSv4: Fix memory leak in nfs4_set_security_label
We leak nfs_fattr and nfs4_label every time we set a security xattr.
In the Linux kernel, the following vulnerability has been resolved:
cachefiles: add consistency check for copen/cread
This prevents malicious processes from completing random copen/cread
requests and crashing the system. Added checks are listed below:
* Generic, copen can only complete open requests, and cread can only
complete read requests.
* For copen, ondemand_id must not be 0, because this indicates that the
request has not been read by the daemon.
* For cread, the object corresponding to fd and req should be the same.
In the Linux kernel, the following vulnerability has been resolved:
cachefiles: Set object to close if ondemand_id < 0 in copen
If copen is maliciously called in the user mode, it may delete the request
corresponding to the random id. And the request may have not been read yet.
Note that when the object is set to reopen, the open request will be done
with the still reopen state in above case. As a result, the request
corresponding to this object is always skipped in select_req function, so
the read request is never completed and blocks other process.
Fix this issue by simply set object to close if its id < 0 in copen.
In the Linux kernel, the following vulnerability has been resolved:
nvme: avoid double free special payload
If a discard request needs to be retried, and that retry may fail before
a new special payload is added, a double free will result. Clear the
RQF_SPECIAL_LOAD when the request is cleaned.
In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: wext: add extra SIOCSIWSCAN data check
In 'cfg80211_wext_siwscan()', add extra check whether number of
channels passed via 'ioctl(sock, SIOCSIWSCAN, ...)' doesn't exceed
IW_MAX_FREQUENCIES and reject invalid request with -EINVAL otherwise.
In the Linux kernel, the following vulnerability has been resolved:
KVM: PPC: Book3S HV: Prevent UAF in kvm_spapr_tce_attach_iommu_group()
Al reported a possible use-after-free (UAF) in kvm_spapr_tce_attach_iommu_group().
It looks up `stt` from tablefd, but then continues to use it after doing
fdput() on the returned fd. After the fdput() the tablefd is free to be
closed by another thread. The close calls kvm_spapr_tce_release() and
then release_spapr_tce_table() (via call_rcu()) which frees `stt`.
Although there are calls to rcu_read_lock() in
kvm_spapr_tce_attach_iommu_group() they are not sufficient to prevent
the UAF, because `stt` is used outside the locked regions.
With an artifcial delay after the fdput() and a userspace program which
triggers the race, KASAN detects the UAF:
BUG: KASAN: slab-use-after-free in kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm]
Read of size 4 at addr c000200027552c30 by task kvm-vfio/2505
CPU: 54 PID: 2505 Comm: kvm-vfio Not tainted 6.10.0-rc3-next-20240612-dirty #1
Hardware name: 8335-GTH POWER9 0x4e1202 opal:skiboot-v6.5.3-35-g1851b2a06 PowerNV
Call Trace:
dump_stack_lvl+0xb4/0x108 (unreliable)
print_report+0x2b4/0x6ec
kasan_report+0x118/0x2b0
__asan_load4+0xb8/0xd0
kvm_spapr_tce_attach_iommu_group+0x298/0x720 [kvm]
kvm_vfio_set_attr+0x524/0xac0 [kvm]
kvm_device_ioctl+0x144/0x240 [kvm]
sys_ioctl+0x62c/0x1810
system_call_exception+0x190/0x440
system_call_vectored_common+0x15c/0x2ec
...
Freed by task 0:
...
kfree+0xec/0x3e0
release_spapr_tce_table+0xd4/0x11c [kvm]
rcu_core+0x568/0x16a0
handle_softirqs+0x23c/0x920
do_softirq_own_stack+0x6c/0x90
do_softirq_own_stack+0x58/0x90
__irq_exit_rcu+0x218/0x2d0
irq_exit+0x30/0x80
arch_local_irq_restore+0x128/0x230
arch_local_irq_enable+0x1c/0x30
cpuidle_enter_state+0x134/0x5cc
cpuidle_enter+0x6c/0xb0
call_cpuidle+0x7c/0x100
do_idle+0x394/0x410
cpu_startup_entry+0x60/0x70
start_secondary+0x3fc/0x410
start_secondary_prolog+0x10/0x14
Fix it by delaying the fdput() until `stt` is no longer in use, which
is effectively the entire function. To keep the patch minimal add a call
to fdput() at each of the existing return paths. Future work can convert
the function to goto or __cleanup style cleanup.
With the fix in place the test case no longer triggers the UAF.
In the Linux kernel, the following vulnerability has been resolved:
ASoC: topology: Fix references to freed memory
Most users after parsing a topology file, release memory used by it, so
having pointer references directly into topology file contents is wrong.
Use devm_kmemdup(), to allocate memory as needed.
In the Linux kernel, the following vulnerability has been resolved:
s390/sclp: Fix sclp_init() cleanup on failure
If sclp_init() fails it only partially cleans up: if there are multiple
failing calls to sclp_init() sclp_state_change_event will be added several
times to sclp_reg_list, which results in the following warning:
------------[ cut here ]------------
list_add double add: new=000003ffe1598c10, prev=000003ffe1598bf0, next=000003ffe1598c10.
WARNING: CPU: 0 PID: 1 at lib/list_debug.c:35 __list_add_valid_or_report+0xde/0xf8
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.10.0-rc3
Krnl PSW : 0404c00180000000 000003ffe0d6076a (__list_add_valid_or_report+0xe2/0xf8)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
...
Call Trace:
[<000003ffe0d6076a>] __list_add_valid_or_report+0xe2/0xf8
([<000003ffe0d60766>] __list_add_valid_or_report+0xde/0xf8)
[<000003ffe0a8d37e>] sclp_init+0x40e/0x450
[<000003ffe00009f2>] do_one_initcall+0x42/0x1e0
[<000003ffe15b77a6>] do_initcalls+0x126/0x150
[<000003ffe15b7a0a>] kernel_init_freeable+0x1ba/0x1f8
[<000003ffe0d6650e>] kernel_init+0x2e/0x180
[<000003ffe000301c>] __ret_from_fork+0x3c/0x60
[<000003ffe0d759ca>] ret_from_fork+0xa/0x30
Fix this by removing sclp_state_change_event from sclp_reg_list when
sclp_init() fails.